Forum Post: RE: I am having trouble with a anlog to digital converter ads1256...
Tom, I know this thread is kind of old, but I was hoping you still had those ADS1256 examples laying around or some code that works between either the MSPEXP430FR4133 or Arduino and the ADS1256 ? My...
View ArticleForum Post: RE: TLV320AIC3253 as standalone
Thanks for your reply. I have some other question: - According AIC3253 and AIC3254 data sheets both supports Digi mic. I noticed in PurePath that there are components as DigiMic, but whe I select...
View ArticleForum Post: RE: DAC7760, characteristics of DVDD Internal Regulator
Hello Eugenio-san, Sorry again. Is the voltage of DVDD Internal Regulator limited from 4.5 V to 4.7 V, although the following article says the voltage of DVDD Internal Regulator is in 4.6V +/- 200mV?...
View ArticleForum Post: RE: GUI DAC3XJ8X GUI
Hello Neeraj, Thanks for what you sent me yesterday. After checking the files, unfortunately, it is not what I need. If it is possible, I would like the vis that does the user GUI (DAC3XJ8X GUI v1.1)...
View ArticleForum Post: ads1293EVM USB driver
Hy there, i have a problem setting up the ads1293EVM . USB-Driver installation fails saying "Hashvalue of the file is not present in the catalog". I tried re-downloading and installing on different...
View ArticleForum Post: RE: ADS1220 How to read temperature
Thank you Bob Sir, I tried using single shot conversion mode and using START command, it is working fine. Now I want to ask one thing that in this temperature sensing mode what is role of DRDY signal?...
View ArticleForum Post: RE: ADS1220 How to read temperature
Ohh.... I forgot to configure interrupt on MCU that's why it was not working. Now It is working with DRDY signal also. Thanks Bob, My issue is solved.
View ArticleForum Post: RE: ADC Selection with Single Ended Analog Input
Hi, In the case of ADS1220 , can I apply both AVDD and DVDD with + 5V supply Best Regards Sharvy
View ArticleForum Post: TLC1518
My current project requires that I capture analog inputs up to 40kHz bandwidth from 4 sources simultaneously. I'm using the TLC1518 as my ADC and I seem to have hit an impasse with this chip. At the...
View ArticleForum Post: TLC1518
My current project requires that I capture analog inputs up to 40kHz bandwidth from 4 sources simultaneously. I'm using the TLC1518 as my ADC and I seem to have hit an impasse with this chip. At the...
View ArticleForum Post: RE: ADC Selection with Single Ended Analog Input
Hi Sharvy Have you considered the ADS8681 for this design? This device has integrated analog front end circuit that can support inputs signals up to +/-12V with a single 5V supply. It is a perfect...
View ArticleForum Post: RE: ADC Selection with Single Ended Analog Input
Dear Vinay, Thanks for the support guys!!. Currently, I don't have any negative input and the input ranges are from 0-5V with resolution 24-Bit with ENOB not lesser than 19 bit. Best Regards Sharvy
View ArticleForum Post: ADS1291 Power Down
Hi, i am using the ADS1291 and want to power him down. I am using Analog 3V3 and Digital 3V3. So i should get 4uW or 1.2uA of power consumption. I put the "PWDN/RESET" PIN low and i still measure...
View ArticleForum Post: RE: ADS1291 Power Down
Hello Michael, I've moved this post from the Medical Forum to the Precision Data Converter Forum, where the ADS1291 is supported. I'm sure you'll find an answer here.
View ArticleForum Post: RE: TSW54J60/ADS54J60 interleaving correction behaviour at fs/4
No success,… Some time ago, I have tried your reference config files from the GUI but I always had the same problem with the interleaving correction. So I don’t think that the problem is related to the...
View ArticleForum Post: RE: AIC3254 EVM how to settting 192K I2S input in master mode
Dear Sir, If we want to analog in/out with EQ setting, we also need provide MCLK/BCLK/LRCLK? or MCLK only?
View ArticleForum Post: ADS7886 conversion data after powerup and restart
Hi Our customer is evaluating this device. They have a question about conversion data after powerup and restart. On the datasheet it is defined as the following spec, I do not understand what this...
View ArticleForum Post: RE: PCM5121 is no audio
Justin-san, I will ask my customer all of the registers value. Now I know the value of some registers after occurrence of the problem. That is as follows: Page 0 / Register 4 : 0x01 Page 0 / Register...
View Article