Forum Post: RE: TVP7002 video horizontal shaking
Hi Steve,Thanks a lot.As I know, it's a basic algorithm to obtain correct alignment that finds a non blanking pixel at each of the edges of the image.How about phase adjustment? Could you give me some...
View ArticleForum Post: RE: TVP 7002 CVBS and S video support
Hi Sirsl,I have the same question about S-Video support.It seems impossible to support S-Video input?Thanks!
View ArticleForum Post: RE: LDC1000EVM Driver issues on Windows 8 and secure boot
This worked for me running Windows 8 in VirtualBox with an Ubuntu host.Mike
View ArticleForum Post: RE: Does ADC12xSxxx series ADC support DC input voltage digitize?
Hi Chengxian,The Equivalent Input Circuit shows the inside of the chip. The 30pF cap is the sampling capacitor which holds the charge representative of the VIN at sample time.So, yes, you can use these...
View ArticleForum Post: RE: Simultaneous DAC and ADC modules wiht TSW1400EVM
Hi,The TSW1400 and the HSDCPro GUI are not designed to support ADC capture and DAC pattern generation simultaneously. Both will physically connect at the same time, but the GUI will support only ADC...
View ArticleForum Post: Single-supply use of DAC8812 AGNDA and AGNDB seem to be connected...
Hello,I am having issues running the DAC8812 on a single supply. I am working from the schematic in the datasheet (Figure 31) with this modification: AGNDA is connected to OPAMP IN+ and forced to a...
View ArticleForum Post: RE: Reference voltage for ADS1278
Reza -Please review the datasheet and the VREF spec. The device only supports a minimum of 0.5V for VREF.For lower reference voltages, instead of the standard buffer, you would need to provide...
View ArticleForum Post: RE: Summing Two 16-Bit DACs for 24-bit Resolution
One more thing - If I were to use DAC9881 I would use the SB grade to make sure I had an 18-bit part. The S grade device has DNL max specified as 2 LSBs.
View ArticleForum Post: RE: DAC3482IZAY ESD classification
Hi Aaron,Please see below for the DAC348x family device ESD rating:DAC3484IRKDT, DAC3482IRKDT, DAC3484IZAY and DAC3482IZAY devices passed below ESD ratings.ESD-HBM: +/- 500V, 1000V, 1500V, 2000V,...
View ArticleClik here to view.
Forum Post: ADS1292R Two electrode ECG
Hi, I'm working with the ADS1292RECG-FE evaluation board. We are developing a two electrode ECG monitor.I'm capturing the signal with the evaluation board's software in the "Live ECG\RESP display" mode...
View ArticleForum Post: RE: ADS1243-HT : RREG command : Can I issue the command one time...
Hi Yuquan,The ADS1243 resolves to the 24-bit level which is the output response. However due to noise, the effective resolution does decrease from the resolution size.When writing your code, you can...
View ArticleForum Post: RE: DAC1280 - single ended output
Hi Raphael,Check out this other similar E2E thread: http://e2e.ti.com/support/data_converters/precision_data_converters/f/73/p/300939/1057291.aspx#1057291The high frequency noise of the DAC1280 and...
View ArticleForum Post: RE: LDC is like wear debris sensor
Hello, Evgeny.The concentration level is around 1500 debris/cm3 and less.Is it really that on high frequency (5MHz for example) the resolution on inductance is less then on low frequency (200-500kHz)?
View ArticleForum Post: RE: TVP5150 interrupt reset
1. I want to switch between Day mode and Night mode, I think I should change the brightness/contrast register. Am I right?2. After I change the brightness controller register, I want to effect the...
View ArticleForum Post: RE: Advance Digital to Analog Converter IC PCM1796 Issue
Hello Don Dapkus ,No Sir this Won't resolve yet, i sent it for redesign with PCM1794 and PCM1792. so if you provide me some reference material and important points to be noted while designing regarding...
View ArticleForum Post: RE: TLV320AIC1106 problem
Hi, Alex,Great! thanks for the confirmation.If you run into trouble, let us know, and we will do our best to help.-d2
View ArticleForum Post: RE: A problem about ADS1281 for amplitude limiting
Dear Chris, the attachments are the schematic of my circuit and new figures for the input plot.The data is the output codes of the ADC which I read by FPGA used the SPI interface.(Please visit the...
View ArticleForum Post: RE: LM97600 using the temperature diode
Hello Jim san, Thank you for the reply.I understood. Best Regards,Ryuji Asaka
View Article