Forum Post: RE: DANCEVM-A eval board
Hi, Jaden,Unfortunately, this board is no longer available.-d2
View ArticleForum Post: RE: ADS7263 How to Use Part II
Hi TomThank you very much for the answer.I wouldl ike to doble check.if the below table works for our input signal condition, Unipolar (0 ~5V) using internal refernce (2.5V). and if it is same for...
View ArticleForum Post: RE: Pc software package to evaluate AD performance
Hi Tom again,The customer would like to evalaute ADS7263 SINAD, ENOB and so on. May I have an idea how to measure them, what tools are required? And do you have some measured data in past in your lab...
View ArticleForum Post: RE: ADS1299 Wiring & Start
Hi Till,I wanted to do same, do you have final code somewhere shared?It will be very helpful for me.Thanks,Ali
View ArticleForum Post: RE: Summing Two 16-Bit DACs for 24-bit Resolution
Chris,So noted. Thanks for pointing this out.Maybe TI will design a precision DAC for more GP purposes in the future.Best Regards,John W.
View ArticleForum Post: RE: ADS42JB69EVM Problem
check below link.http://www.windowserrorhelps.com/libusb0-dll-error-repair-fix-libusb0-dll-as-quickly-as-you-can
View ArticleForum Post: LDC is like wear debris sensor
Hi! I'm going to use the LDC evm (I had it already) like a wear debris sensor. I want to register small wear debris in fluid flow. I suppose the fluid with debris will flows through L-tank (in plastic...
View ArticleForum Post: RE: external clock adc12d1800rfrb not working
Ok.Just to be sure: if I change position of R180 can I use only external clock and the internal clock is floating?I will try and I will give you an update.Thanks a lot.Best regardsGiuseppe Gottardo
View ArticleForum Post: ADS1192 ECG_FE code source
Hi,I really can not find the ADS1192 ECG_FE code source, there is only 1298 code in the file, and the msp430 of ADS1192 ECG_FE is msp430f5529. Anyone knows how to get the code of ADS1192 ECG_FE?...
View ArticleForum Post: RE: TVP5150 interrupt reset
Thank you very much!1. But I thinke the answer of question 1 and 5 seem contradictory. Can Software initialization reset bit(bit 7 of 0x1C) reset the whole CPU of TVP5150?...
View ArticleForum Post: RE: ADS1192ECG_FE Firmware
Hi,I also want to buy the ADS1192ECG_FE, and I am looking for the software of it, but I can not find it on line, could you tell me how to get the code of ADS1192ECG_FE ? thanks a lot !!!
View ArticleForum Post: RE: PCM5122 PLL on BCLK
Looks like the PLL multiplier was too low and it was out-of-spec. I will test again with larger multipliers.
View ArticleForum Post: Reference voltage for ADS1278
Hi everyone,I need 0.4V or 0.6V reference voltage for ADS1278 data converter and in datasheet of ADS1278, Ref5025 is offered which produce 2.5. How can I reach 0.4 or 0.6V?ThanksReza
View ArticleForum Post: RE: LDC1000EVM, CFB capacitor
Thanks.And How about my last post:"Hi, Now I'm testing another coil with inductance 17 uF and Rp min = 200 ohms and Rp max = 5 K ohms. The parallel capacitor has value of 4.7 nF, so the frequency is...
View ArticleForum Post: RE: ADS1241 Registers
Hi Bob, I got the timing issue resolved, so disregard the above!
View ArticleForum Post: RE: Strange Results from ADS131E08
If it helps at all, I tried various spi clock's from 1mhz to 8 mhz and it doesn't appear to make any difference, always strange output below a certain value.SPI Interface is Mode1
View ArticleForum Post: set up the LM96511 evaluation board with WaveVision 5 (issue with...
Hi,We are trying to set up the LM96511 evaluation kit along with the WaveVision 5 data capture board on Windows 7. We could install the hardware (as it is recognized by the system). We also set up...
View ArticleForum Post: RE: external clock adc12d1800rfrb not working
Hello Giuseppe,That is correct. Additionally setting the clocking mode to external in WaveVision will disable the LMX2541 output. This is important to prevent any crosstalk on the clock.Let me know how...
View ArticleForum Post: RE: What does the ADS5483 generate when there is nothing...
Hi,That condition is what is called idle-channel noise. There is a spec for idle channel noise in the datasheet on page 6 as well as a histogram out output codes with zero differential input voltage...
View ArticleForum Post: ADS1255 continuous reading
We use the ADS1255 ADC in a new product. The data sheet details how to read from the chip, but does not address an issue of importance to our design. The processor used in our design needs to use as...
View Article