Forum Post: RE: TSC2004: Touch Screen not responding properly.
Hi Daveon, Have you had a chance to review the configuration?
View ArticleForum Post: RE: ADS7038-Q1: ADS7038
Hi Joël, Thanks for the answers. I do not have a problem with calibrating the device, just need to decide whether I shall make it a regular task of not. About the third point: to me, the datasheet...
View ArticleForum Post: RE: ADS1261: 2 wire excitation mode problem
Hi Bryan, Thanks, I will perform this tests during these days and I will let you know something! Elia
View ArticleForum Post: RE: ADS131M02: AC-coupled input help for ADS131M02
Hi Dale, Thank you for your info. The op-amp is configed as the differential buffer like the first stage of an instrumentation amp with a gain of 100 on each. So a 1mV diff signal will be amplified to...
View ArticleForum Post: RE: DAC80516EVM: I2C protocol not reaching
Hi Erin, Exactly, I’m scanning addresses from 0 to 128 to catch all possible I2C addresses. As for the clock speed, it's currently set between 350 and 400 kHz, which should be low enough, I believe....
View ArticleForum Post: RE: ADC3422: test PRBS generated on LVDS outputs
Hi Chase, I tested you file with the FPGA simulator, the PRBS checker locks after several samples and then remains locked. PRBS checker works. Your data sequence is perfect. I'm trying now to...
View ArticleForum Post: ADS1015-Q1: I2C Write failure problem
Part Number: ADS1015-Q1 Tool/software: Hi team， Harman are currently integrating the ADS1015-Q1 into our software system and have encountered an issue that requires your expertise to resolve. Here are...
View ArticleForum Post: ADS131M04: READ AND WRITE ISSUE
Part Number: ADS131M04 Tool/software: Hi im using ADS131M04, im trying to communicate with the ic, im reading the default registers value, but data is incorrect.in the just trying to read the mode...
View ArticleForum Post: ADS6445: Serial interface acknowledge signal
Part Number: ADS6445 Tool/software: Hi, 1. Can anyone tell me after configuring the serial registers on the ADC does the master receive any acknowledge signal back?. I did not find it neither on the...
View ArticleForum Post: ADS131B02-Q1: Switching CHn_CFG from Test Signal to AIN1P/AIN1N
Part Number: ADS131B02-Q1 Tool/software: Hi Ti Support Team, I am currently using the CH1_CFG setting to 10b (Positive DC test signal) to output a test signal and calculate Vref. This is primarily for...
View ArticleForum Post: RE: ADC3422: test PRBS generated on LVDS outputs
Hi Andrea, I used 50MSPS. The align bit doesn’t need to be on for PRBS to work. It worked fine on individual or more than one channel, but just not aligned. I’d suggest running at 25MSPS or something...
View ArticleForum Post: RE: DAC81401: Voltage sense - use of VSENSEN input
Hello Sanjay, Thanks for the hint. Is the DAC81402 not just a dual DAC81401, then? I see that block diagrams in the respective data sheets do have some differences related to the sense inputs. Please...
View ArticleForum Post: ADS124S06: About REFCOM pin connection in bipolar supply case
Part Number: ADS124S06 Tool/software: Hi all, I'm debugging a power supply issue on a board. It seems that the power supply chip sees low impedance (or a soft short) at the output, which limits the...
View ArticleForum Post: RE: ADC3422: test PRBS generated on LVDS outputs
> The align bit doesn’t need to be on for PRBS to work. This is very strange. In my configuration without sync it goes completely nuts, so in PRBS mode it has a completely different behavior. Other...
View ArticleForum Post: RE: TI-JESD204-IP: Getting to link up / PRBS testing with...
Hi Aiden, The TI IP version with automated block design support was ultimately not released because most customers have preferred doing this on their own. Adding a verilog wrapper over the top level...
View ArticleForum Post: RE: AFE5805: Reference design
You can refer to the AFE5805EVM for reference.
View ArticleForum Post: RE: AFE5805: Reference designs
Duplicate thread e2e.ti.com/.../afe5805-reference-design
View ArticleForum Post: RE: TI-JESD204-IP: Getting to link up / PRBS testing with...
Hi Ameet, Nice to meet the author of the IP, and thanks for taking the time to reply. It does answer my question about point 1 regarding the decision to not implement the block design support....
View ArticleForum Post: RE: ADC3422: test PRBS generated on LVDS outputs
Hi Andrea, To me personally, I don't know how to decode the package markings. I'm asking around for info on this. I'll let you know if there is any concerns with it. If you have other device you can...
View ArticleForum Post: TPS562203: TPS562203 vs TPS562231
Part Number: TPS562203 Other Parts Discussed in Thread: TPS562231 Tool/software: This part has a newer version TPS562231. So seek you help to advise whether TPS562231 will go to EOL soon. If yes, pls...
View Article