Forum Post: RE: UCC28C43: Letter of Volatility Request
Hi, It looks you had thread (+) UCC28C43: Letter of Volatility Request - Data converters forum - Data converters - TI E2E support forums Why cannot you work Alex Segler to get this?
View ArticleForum Post: RE: UCC28C43: Letter of Volatility Request
Hi, Based on my check with the responsible team, this device does not have digital memory so volatility is not applicable to this device.
View ArticleForum Post: RE: ADC3660: Changing DCLKIN changes measurements
Hi Tom, I assume you are not decimating, you are in bypass mode? Most likely 12MSPS sampling works, is that your Frame clock and data clock at exact multiples of each other, factor of 8 and so is the...
View ArticleForum Post: RE: ADC3660: Changing DCLKIN changes measurements
Hi Tom, I cannot comment on why the data seems to be correct when the incorrect DCLK frequency is provided. I would recommend using the device as it is documented in the datasheet if you would like it...
View ArticleForum Post: RE: ADS125H02: Testing (of digital parts) with only DVDD possible?
Hi nameduser, The ADS125H02 has a power-on RESET (POR) that will not trigger until all supplies are established, see below. Communication is unavailable until the POR releases, so you will not be able...
View ArticleForum Post: RE: AFE4300EVM-PDK: Data register, where can i find?
Hello Muhammad, Thank you for your interest in our device. The AFE4300 datasheet is under NDA, and requires special permission to access. You can request access here:...
View ArticleForum Post: RE: ADS7951: Rogowski coil data acquisition
Hi Joel, Thank you for your reply. I will need a 12 channel ADC. The signals to be measured will be 50Hz, so I am leaning towards at least 500k Sample per second and 12-bit resolution. I have...
View ArticleForum Post: DAC63204-Q1: Setup for simple voltage output
Part Number: DAC63204-Q1 Tool/software: Hello, Can you please advice the register configurations required to use the DAC as a simple voltage output? It will use VDD as the reference, My circuit has...
View ArticleForum Post: RE: LM2596S-ADJEVM: LM2596S-ADJEVM
Hello I will check with our PE and get back to you as soon as possible. Thanks
View ArticleForum Post: RE: AMC1303M0520: Letter of Volatility Request
Closing this thread and responding to duplicate one.
View ArticleForum Post: RE: AMC1303M0520: Letter of Volatility Request
Hi James, I will reach out to my team and see if we can get this for you. Thank you, Eva
View ArticleForum Post: RE: DAC8742H: Does DAC8742H has passed the physical layer test of...
Thong, I'll check on the filter construction. I pulled up the topology of the filter from an internal presentation on the modem transmit and receive. However, I think the numbers I saw in the...
View ArticleForum Post: DAC53204: No response on SDO in 4-Wire SPI after enabling GPO and...
Part Number: DAC53204 Tool/software: Hello, I am trying to get proper communication with my DAC53204 device and believe I am sending the proper commands in order to enter 4-Wire SPI mode. The issue is...
View ArticleForum Post: RE: UCC28C43: Letter of Volatility Request
Hi, Based on my check with the responsible team, this device does not have digital memory so volatility is not applicable to this device.
View ArticleForum Post: RE: UCC28C43: Letter of Volatility Request
Ok. Can you confirm that this device does NOT contain volatile or non-volatile memory?
View ArticleForum Post: RE: UCC28C43: Letter of Volatility Request
Hi, This is an analog device so no memory is used.
View ArticleForum Post: RE: DAC60501: SPI communication problem
Hi Phillip, This device clocks data in on the falling edge of SCLK. Your SPI communication is set up for rising edge. See if fixing the SPI configuration solves this issue. Thanks, Erin
View ArticleForum Post: RE: TSC2007: x, y axis changed reaction problem
Hi, Have you tried switching the connection of your X1 and Y1 to the board? Otherwise maybe you could fix it in your software solution. This seems like it would be a touch panel issue and not...
View ArticleForum Post: RE: DAC714: What is meaning -1of DAC712U-1?
Hi Jimmy, The -1 denotes a 1k reel. In this case, the DAC712U-1 is the same as the DAC714U/1k indicator. Thanks, Erin
View ArticleForum Post: RE: ADS1261: Responding with All Zeros
Hi Everett Everett, Your SCLK must idle low at all times. You can see in the images below that SCLK is idling high for 100s of microseconds, can you fix this? Basically you should only be toggling...
View Article
