Forum Post: ADC128S022: The rise time of the SCLK pin's rising edge.
Part Number: ADC128S022 Tool/software: Hello, I am designing a circuit using the ADC128S022 in a mixed 5V and 3.3V environment. The microcontroller operates at 3.3V, while the ADC128S022 is powered at...
View ArticleForum Post: DAC8775: Open Circuit Condition
Part Number: DAC8775 Tool/software: Hi, I was unable to perform testing earlier due to other commitments, but I have now resumed debugging this issue. In continuation of the discussion in the link...
View ArticleForum Post: ADS7845: Four wire capacitive display IC support
Part Number: ADS7845 Tool/software: As we mentioned above we need to know about a touch controller(Four wire capacitive display) which has similar pin mapping as ADS7845.
View ArticleForum Post: DAC5681Z: single ended support
Part Number: DAC5681Z Tool/software: I want to use the DAC5681Z in a single-ended, and I want to make it using the drawing below. Is that possible?
View ArticleForum Post: RE: ADS127L11: DRDY-pin is not getting low
Hello Keith, Thank you for your reply. adding half of SCK cycle between filing edge of /CS and first rising edge of SCK solved the problem. I am getting DRDY at 50KHZ. Thank you very much for great...
View ArticleForum Post: ADC3664EVM: HSDC pro v6.0 for ADC3664EVM
Part Number: ADC3664EVM Tool/software: Dear Technical Support Team, I installed sbac273.zip(HSDCPro Patch v5.00.06) and HSDC pro v6.0. But HSDC shows following message. TI web provide only HSDC pro...
View ArticleForum Post: AMC131M03: Is it possible to measure both AC and DC voltage...
Part Number: AMC131M03 Tool/software: Is it possible to measure both AC and DC voltage simultaneously using a single this IC? , if yes can you suggesty any circuit reference can i use pins 6,7, 8 for...
View ArticleForum Post: ADS8684: Sampling range missing
Part Number: ADS8684 Tool/software: Using your ADS8684A4 channel AD acquisition chip, we are experiencing the following problems. Hardware using internal reference voltage, measured as 4.086V 1....
View ArticleForum Post: AMC1306M25: What is the DC accuracy parameter from -250mV to...
Part Number: AMC1306M25 Tool/software: hi I want to know the DC accuracy parameter from -250mV to -320mV and 250mV to 320mV for a worst Case Calculation， could you provid it？ thank you！
View ArticleForum Post: RE: ADS7958: MUX staying in ch0 and not switching further
Hi Joel, Thanks for the detailed reply, Cause of this issue was spi-cpha was enabled in the device tree which worked with our older revision boards, But didn't work with the newer version as said...
View ArticleForum Post: RE: ADC12DJ5200-SP: how to use clock chip LMX2594RHAR and...
Hi Rob, please privide us ADC12DJ5200RFAVV code, we use this chip, need to software, thanks!
View ArticleForum Post: ADS1278-SP: Power Consumption Vs Fclk
Part Number: ADS1278-SP Tool/software: Hello everyone! I have a doubt about the power consumption of the part at different clock frequencies. In the datsheet power consumption is detailed at a fclk of...
View ArticleForum Post: RE: ADC34J23EVM: Unable to configure ADC & LMK04828 using ADC3000...
Hi Rob, Yes, as mentioned in earlier exchanges, I go on the Common Tab in the GUI and check the Global Power Down checkbox. However, the current consumption does not go down even a bit, pointing out...
View ArticleForum Post: RE: ADS1294R: Schematic Review Request
Hello Ryan, Thank you very much for taking the time to review my schematic and provide this feedback. I'm greatly thankful for your help. Have a nice day! Best regards, Pierrick
View ArticleForum Post: RE: ADS7128: How to correctly use RMS
Hi Joel. Sorry for late response. We use 1uF ceramic capacitors, as recommended in the datasheet. I check the voltage with oscilloscope and it looks OK for me. 3.3V digital, this voltage is more rush,...
View ArticleForum Post: ADS8319: What is occurred when the input+/- impedance is not...
Part Number: ADS8319 Other Parts Discussed in Thread: ADS8361 Tool/software: Hello guys, One of my customers is designing their next products circuit using ADS8319. At this moment, they have the...
View ArticleForum Post: RE: ADC12DJ5200-SP: how to use clock chip LMX2594RHAR and...
Hi Rob, please provide us JESD204C IP, use intel FPGA AGIB027R31B and two pcs ADC ADC12DJ5200RFAVV, thanks!
View ArticleForum Post: ADS1292R: ADS1292R Resp
Part Number: ADS1292R Tool/software: Hello everyone We use ADS1292R in bipolar mode ; +/-2.5V . i saw ithe evalution kit for respiration part there is an high pass filter at the inputs with pull up...
View ArticleForum Post: RE: ADS131M08: WREG command
Hi Dale, My READ command is working—I can read the registers correctly. All of them return their respective default values according to the datasheet. The problem is related to the WRITE operation and...
View ArticleForum Post: RE: ADS8684: Sampling range missing
Hi There! Welcome to our e2e forum! Please provide some additional details - clearer schematic if possible with any details on the input driver circuits used ahead of the ADC inputs. Raw data showing...
View Article