Forum Post: RE: ADC12DJ5200RFEVM: Request for Information: ADC12DJ5200RFEVM...
Hi Balu, Closing this post and will work with you offline. Thanks, Rob
View ArticleForum Post: RE: ADC3562: Regarding AINM pin processing when using AD...
Hi Oda, The ADC fullscale is 3.2Vpp differential. So each input would be 1.6Vpp per P/N input. This 1.6V is biased around a 0.95V DC common mode voltage or +/-800mVpk. Hope that helps. I would use the...
View ArticleForum Post: RE: ADC3664: Amplitude Calculation of the sinusoidal input.
Hi Fenil, I would capture and display the output data in either a Time Domain or Frequency domain and you can correlate from there. If you download HSDCPro, this will give you an idea of how the data...
View ArticleForum Post: RE: ADS42LB69: Function of TEST PAT ALIGN field in register 8
Hi Keisuke, How is this test being setup? Are you using the ADC EVM or your own board design? Regards, Rob
View ArticleForum Post: RE: ADC3569: JESD204B version of 16-bit 500MSPS ADC
Replied to customer in direct email.
View ArticleForum Post: RE: ADS9813EVM: Confusion regarding initialization sequence of...
Hi CT, The confirmed sequence is as follows: 0x000B to 0x04 address 0x0002 to 0x03 address // select register bank 1 0x0002 to 0x92 address 0x0604 to 0xC5 address Yes, PHA and POL being 0 is correct...
View ArticleForum Post: RE: ADS7138-Q1: ADS7138-Q1
Hello Babu, The ADS1015-Q1 is a 12-bit, 4-ch ADC that takes both differential and single-ended input. Would this device solve your problem? Also, is this device being used in OBC or DC/DC? Regards,...
View ArticleForum Post: RE: ADS7128: How to correctly use RMS
Hi Daniel, I think all that the ""ninth falling edge of SCL" denotes is marking the start of the next conversion period once data for the current conversion has been read out. In terms of implementing...
View ArticleForum Post: AFE58JD18EVM: HMC_DAQ GUI - Device Communication Error
Part Number: AFE58JD18EVM Other Parts Discussed in Thread: AFE58JD18 Tool/software: Using the SLOC326 HMC_DAQ GUI for the AFE58JD18 EVM and getting an error trying to connect to the board. Device...
View ArticleForum Post: RE: AFE58JD18EVM: HMC_DAQ GUI - Device Communication Error
Note: I enabled the .NET Framework 3.5 to allow for GUI use with Windows 10 as was suggested in another forum.
View ArticleForum Post: RE: DAC38J82EVM: and TSW14J57EVM unreliable - DAC fails to output...
Hi Ti team, Could someone give some attention to this matter as this issue has considerably slowed down/stopped our progress on the evaluation work on the DAC38RF82EVM. Note that I have the same issue...
View ArticleForum Post: DAC8830-EP: VDD pin
Part Number: DAC8830-EP Tool/software: Hi there, on the DAC8830-EP datasheet SGLS334C (revised 2007) on page 7 the VDD pin is listed as 'Analog power'. By looking at the device architecture,...
View ArticleForum Post: RE: TLA2528: Sampling Effect
Hi WorkerBee, Could it be something from the Analog Engineer's Calculator ? There are many options here, so I would recommend downloading it and taking a look to see if you find what you're looking...
View ArticleForum Post: RE: AMC131M03: Is it possible to measure the 3 phases using the...
Hi Manikanta, You can measure the phases without Neutral. You could place the device on one of the phases and have a voltage divider to the other two, or you could put the device on a floating node...
View ArticleForum Post: RE: ADS1115: ADS115 used to find the voltage difference between...
Hi Vignesh, [quote userid="639786"...
View ArticleForum Post: RE: ADS131M04-Q1: Help Needed: Basic Communication Between...
Hi KIRYOUNG YANG, Can you clarify "Channels 1 and 2 share the same negative analog input"? Did you just short AIN1N and AIN2N together or short them together then connect them to a signal source? It...
View ArticleForum Post: RE: ADS124S08: Switching in multiple references
Here a couple pages of the ADC. schematic area. I am switching in the references via an analog switch. I have verified this does work and the appropriate voltage is making it to the REF pin. Basically...
View ArticleForum Post: RE: ADC12DJ5200-SP: how to use clock chip LMX2594RHAR and...
Hi Xiaoqiu, I assume you mean 19W for the entire board? Seems a little high, unless you are dropping alot of voltage/power across the LDOs or power supplies to get to 1.1V and 1.9V. The schematic...
View ArticleForum Post: RE: ADS8588S: ADC and AFE recommendation
OK then, the ADS8588 or ADS8688 would be the best option we have at the moment.
View ArticleForum Post: RE: ADS7056: Data acquisition without FPGA
Hi engiz, I'm basing myself off of the document that I've attached below. Roughly speaking, the FPC cables at a worst case have a dielectric constant of 4.0, and as the dielectric constant goes up, so...
View Article