Forum Post: RE: ADS1118EVM: TI Web GUI Data Capture Not drawing line between...
Hi Erric, I've had limited computer access due to travel. I believe you were referring to the following icons being grayed out: To export data captured by the GUI, you go to File, Analysis Data, and...
View ArticleForum Post: RE: DAC8742H: Does DAC8742H has passed the physical layer test of...
Thong, I'm still not sure what the problem is at this point, but I did have some extra questions. How do you generate the jitter in your setup? Do you use a specialized test system? At this point, I...
View ArticleForum Post: RE: ADS1288: ADS1288
Hi Lkhagvajantsan, The 4-channel electrical grid ADCs could all be good fits for your application. They are designed for the low frequency range. https://www.ti.com/product/ADS131E04...
View ArticleForum Post: RE: DAC8574: Problem: reading back a value from DAC8574
Hi Marcel, I will try to confirm this behavior on the EVM. Best, Katlynne Jones
View ArticleForum Post: RE: ADS7280: ADC configuration
Hi Nick, While I couldn't find anything very similar, we have some example code for SPI interfaces: https://www.ti.com/tool/download/ADS7038-C-EXAMPLE-CODE Additionally, we have started aggregating...
View ArticleForum Post: RE: DAC60501: Power up not going to zero volts
Hi Adam, A) Not as far as I know, and I'm not seeing anything documented internally. All pins have the same input protection (ESD diode to VDD/ground). B) I don't see anything risky with the...
View ArticleForum Post: RE: ADS1232: 3.3V Operation
Hello Tom, I dug through our data, and we have very little data with AVDD=3.3V. Noise is measured with AVDD=3V, and can be found in tables 7-3 and 7-4 of the ADS1232 datasheet. Also, we do specify...
View ArticleForum Post: RE: ADS9219EVM: operating temperature range
Thank you for the feedback Andrei, We like to learn how customers use our devices, the more we understand the better we can address it moving forward. I can confirm that the device, ADS9219, should...
View ArticleForum Post: RE: ADC12QJ1600EVM: FT_DEVICE_NOT_FOUND
Hi Rob, I tried opening it in the admin mode, still same issue. Thanks, Manthan
View ArticleForum Post: RE: ADS131E06:Bits of data read are inverted.
Hi Dale, When Ethernet communication is not performed The trigger for detecting data corruption is not engaged. Noise originating from the communication is definitely having an effect. As far as the...
View ArticleForum Post: RE: ADS1232: 3.3V Operation
Thanks for the prompt answer to my question, Keith.
View ArticleForum Post: ADS1220: Issue with Disabling PGA on ADS1220 – Unexpected Gain...
Part Number: ADS1220 Tool/software: Hello, I am working with the ADS1220 in an application where it is necessary to disable the PGA because the signal is not at the common mode level. According to...
View ArticleForum Post: LMP90100: SPI Data Read issue, LSB not reading correctly.
Part Number: LMP90100 Tool/software: This is follow-up question to https://e2e.ti.com/support/data-converters-group/data-converters/f/data-converters-forum/188380/lmp90100-spi-interface I am following...
View ArticleForum Post: DAC81402: Reference design of Bipolar Output DAC81402
Part Number: DAC81402 Tool/software: Is there any documentation on a reference design for using the DAC81402 with a bipolar output of ±10V?
View ArticleForum Post: RE: ADS7142: Offset Calibration Issue
Really, my question is why isn't TRIG_OFFCAL working when we write to it. We write 0x8 followed by 0x15 followed by 0x1 and nothing happens to the offset. We write 0x6 on a general call and the offset...
View ArticleForum Post: RE: ADC12DJ3200EVM: Comma Character for JESD204B
Hi Chase, I am going through TI204C IP user guide and found that guidelines for accurate sampling of sysref (section 6.6). I am getting sysref and lmfc pulse alignment slightly different as shown in...
View ArticleForum Post: RE: TSC2046E: Linux Driver for TSC2046E TOUCH CONTROLLER
Hello, any update?
View ArticleForum Post: RE: ADC12DJ3200EVM: Comma Character for JESD204B
Hi Raj, I am summarizing some of points discussed in this thread: 1) The ADC12DJ3200 is compliant with the jesd204b Standard. It uses K28.5 as the comma character in the initial CGS sequence. The...
View ArticleForum Post: RE: DDS39RF10: TI JESD204C IP Interfacing with DDS39RF10 part
Dear Sir, I apologise for the confusion created by mentioning DDS39RF10 instead of DAC39RF10. We have DAC39RF10EVM board with us. It will be great if you can make a reference design on KCU105...
View Article