Forum Post: TI-JESD204-IP: ADS52J90 K value =3 for 4 lane mode JESD IP does...
Part Number: TI-JESD204-IP Other Parts Discussed in Thread: ADS52J90 Tool/software: Hello, I am not sure if this question to be asked in ADS52J900 specific thread but since related to JESD IP, posting...
View ArticleForum Post: RE: ADC12DJ5200RFEVM: On-Board clocking issues
HI Jeff, We have verified this works with external clocking, I believe there are a few settings that need to be made in the GUI on the clocking tab in order to make this run. I will respond early next...
View ArticleForum Post: RE: ADS4128: Weird phenomena with ADC Clock output
Hi Georgios, Thanks for the details. Are you using our TI evaluation board connected to a Xilinx dev kit? If not, you may need to send over your schematics to see what the issue is. Regards, Rob
View ArticleForum Post: RE: AMC131M03: SPI communication with the device
Hi Valeriy, [quote userid="577072" url="~/support/data-converters-group/data-converters/f/data-converters-forum/1431288/amc131m03-spi-communication-with-the-device/5506309#5506309"]I did not know I...
View ArticleForum Post: RE: AMC130M02: AMC130M02 configuration
Hi Bruce, [quote userid="604788" url="~/support/data-converters-group/data-converters/f/data-converters-forum/1435994/amc130m02-amc130m02-configuration"]Should there always be a voltage (we measured...
View ArticleForum Post: RE: ADS1299: Collecting small signals, with correct amplitude but...
Hi Ryan， I will show you the results of my logic analyzer measuring SPI communication. As shown in Figure 1, before reading channel data, the DRDY signal remains low and appears to have a pulse...
View ArticleForum Post: RE: ADS1015: part failing with unused inputs in a 24v system
Hello Scott, Thank you for your patience. Answers are shown after your question below. 1. Is it normal for these kind of failures when there is no input protection circuitry? Answer: The analog inputs...
View ArticleForum Post: ADC12DL1500: Request for offline files
Part Number: ADC12DL1500 Other Parts Discussed in Thread: TSW14DL3200EVM Tool/software: Hi, the thread title says it all I guess. I'd like the reference design files of 1500, 2500(if different), and...
View ArticleForum Post: DAC5672: BPSK Generation Application
Part Number: DAC5672 Tool/software: Hello Team, we want to generate a 600Hz sine wave output by using :channel-A of DAC5672 & channel B is unused. the code is generated by FPGA. The FPGA provides...
View ArticleForum Post: RE: LMP92066: LMP92066
Hi Erin, In LDMOS mode of biasing, I want the to set the FETDRV0 and FETDRV1 pin to 0V. Please tell me the DAC values for the same.
View ArticleForum Post: RE: ADC12DJ5200RFEVM: On-Board clocking issues
Thanks Rob - We've had consistent success with this mode/rate using external clocking as well. But the on-board clocking (no external clocks at all) is where we're seeing issues. (user guide section...
View ArticleForum Post: ADS1015: ADC1015 - Is a delay between Set MUX via configuration...
Part Number: ADS1015 Tool/software: I am trying to use an ADS1015 in a Meadow environment. I need to switch the MUX input and scroll through a number of channels on 3 devices. I am using single shot...
View ArticleForum Post: ADS131B24-Q1: ADS131B24-Q1 : hall effect current sensor
Part Number: ADS131B24-Q1 Tool/software: Hii I am planning to use ADS131B24-Q1 for desgining of HEV BMS. in order to measure current can we use hall effect current sensor instead of shunt . is there...
View ArticleForum Post: RE: ADS8698: SPI communication and CLK timing, getting same Non...
Hello, Tom Sorry for late reply I am passing 3.3v on channel 0 using potentiometer, and expected to get 3.3.v voltage but getting output in range of 2.1v to 2.8v and it fluctuates a lot, I was...
View ArticleForum Post: RE: ADC12DJ5200RFEVM: On-Board clocking issues
Hi Jeff, Can you send me a picture of your EVM. Close up view so I can see the soldering modifications? We have had a few customers make incorrect modifications. So it would be good for me to verify...
View ArticleForum Post: AMC1303M0510: simultaneous sampling of phase currents not...
Part Number: AMC1303M0510 Tool/software: Hello Experts, We are currently using the AMC1303M0510 to measure two phase currents in our custom motor driver board using the TMS320F28379D 's SDFM module....
View ArticleForum Post: DAC63002: Using an external reference with the DAC63002
Part Number: DAC63002 Tool/software: I am using it by connecting an external reference to DAC63002. Signals are being sent via SPI communication. Under normal conditions, there is almost no current...
View ArticleForum Post: RE: ADS112C04: Temp Accuracy over 1°C
Hi Bryan, Thanks for your feedback. I have below question, please help explain & confirm. 1. What conditions does accuracy type refer to ? ( RTD temperature, IC temperature, voltage...
View ArticleForum Post: RE: ADC12D1600RB: ADC12D1600RB
Hi Robert, The QML package and commercial EVM and sockets are not compatible. Its unclear for which package you want the socket part number and vendor? Please advise, and I can get that information to...
View Article