Forum Post: RE: ADS1298RECGFE-PDK: ADS1298RECGFE-PDK
Set the number of samples to collect to 300,000 and channel data rate for 1kSPS. Then the EVM should run for 5 minutes once you click Capture. More time may be needed for the data to transfer to the...
View ArticleForum Post: RE: ADS7138-Q1: ADS7138QRTERQ1
We are using the two ADs7138-q1 both are connected in parallel , now I need to read the AIN0 ADC pin in both Ic's, how to select the AIN0 ADC channel in Both IC one by one and read the adc data...
View ArticleForum Post: RE: TSC2004: Touchscreen isn't responding
Thank You. I think it would help us to understand how to access the testing mode and how to check if the testing mode is activated.
View ArticleForum Post: RE: ADS1298RECGFE-PDK: ADS1298RECGFE-PDK
Thank you a lot Ryan. Where could I find the option defining the number of samples? Regards Elzbieta
View ArticleForum Post: RE: Anuncio8168:I can't write to the SEQ_START register.
Hola, Hice algunos cambios en mi codigo y ahora mismo me encuento con el siguiente problema (que no lo soluciona ni apargar y encender ni resetear el dispositivo): He programado los registros del ADC...
View ArticleForum Post: DAC63204EVM: Output sin wave waveforms as AC voltage
Part Number: DAC63204EVM Other Parts Discussed in Thread: DAC43608 , DAC43508 Tool/software: Hi, ・Can the DAC63204EVM output sin wave waveforms such as AC voltage? (50Hz, 60Hz, 5Vpp) ・Is it possible...
View ArticleForum Post: ADC12QJ1600EVM: Evaluation Board and Reference FPGA Designs
Part Number: ADC12QJ1600EVM Other Parts Discussed in Thread: TSW14J59EVM , TSW14J57EVM Tool/software: Hi, I am starting to work with the ADC12QJ1600EVM and I have some few questions: The...
View ArticleForum Post: DAC8775: Surge issue
Part Number: DAC8775 Tool/software: Hi, we designed a circuit with DAC8775 following the TI EVM wiring diagrams: https://www.ti.com/tool/TIPD216 This EVM has been tested to pass EMC tests but there is...
View ArticleForum Post: RE: ADS8866: ads8866
Samiha. Thanks a lot for your help. What I'm trying to do is to use a analog multiplex (either 8 or 16 inputs), feed it into RCV420 , a current to voltage converter from Texas and feed the ADC with an...
View ArticleForum Post: ADC3661: How to close timing without tCD maximum specified?
Part Number: ADC3661 Tool/software: The datasheet for the ADC3661 (SBAS991B, revised March 2022) has minimum and nominal numbers for tCD on page 13, but doesn't have maximum numbers. It seems like we...
View ArticleForum Post: RE: ADS8866: ads8866
Hi Andre, Yes, that should be okay. I am linking a video on how gain/offset calibration may be done: https://www.ti.com/video/5466249277001 . Your method sounds similar and okay. Best regards, Samiha
View ArticleForum Post: RE: ADS1258: How to disable or avoid idle/standby mode
I will have to abandon the TI part as you've clearly stated that this part only supports the 4 built in sample rates. Or, more to the point, the START signal cannot be used on this part to control the...
View ArticleForum Post: RE: AFE11612-SEP: USB2ANY, or alternative SPI controller with API
Hi Caleb, The GUI was made to work with the FTDI controller on the EVM board. For device analysis, you can connect the EVM to your computer with a USB cable and use the GUI to interact with it. The...
View ArticleForum Post: RE: AMC131M03: SPI communication with the device
Saleh, [quote userid="593855" url="~/support/data-converters-group/data-converters/f/data-converters-forum/1431288/amc131m03-spi-communication-with-the-device/5503965#5503965"]It's recommended to...
View ArticleForum Post: RE: DAC38J84: DAC register is all 0 when software reset
Hi, Please make sure you have properply reset the DAC and also changed the SPI to 3 wire or 4 wire mode accordingly You may do a test read to check for version ID through register 0x80
View ArticleForum Post: RE: DAC8775: Surge issue
Hi Davide, We are reviewing this and will be able to respond with more information soon. Does your circuit match the TIPD216 schematic exactly? And to clarify, you didn't see surge damage when the...
View ArticleForum Post: RE: ADC12DJ5200RFEVM: On-Board clocking issues
Thank you Jeff for the details. I will fire this up tomorrow on the lab bench and provide an update. Thanks, Rob
View ArticleForum Post: RE: ADS9219EVM: One Lane, DDR mode support - Is Data Averaging...
Hello Panneer Raja, Both are very good questions that bring up some corrections/additions needed in the datasheet, thank you for bringing this up. For your 1st question, Yes, it is applicable for the...
View ArticleForum Post: RE: ADC101C021: Pull-up resistor voltage
Hell samiha-san Thank you for your reply. According to the datasheet, the type of the ALERT terminal is Digital Output. Is it OK to consider that Operating Ratings (3) applies in this case as well?...
View ArticleForum Post: RE: ADS8698: SPI communication and CLK timing, getting same Non...
Hi Ernist, Any luck with finding an o'scope or LA?
View Article