Forum Post: RE: ADS131E08: Read Data with RDATA command and the result is...
Hi Zhang, I need to discuss with my team and will get back to you by end of business on Monday. Regards, Keith
View ArticleForum Post: ADC12DJ5200-SP: CLK_P/N and SYSREF Input Waveforms
Part Number: ADC12DJ5200-SP Tool/software: Hello, I"m attempting to use an LMX2615 device to feed the CLK_N/P and SYSREF_P/N of the ADC12DJ5200-SP. We're doing LVPECL and I'm getting a waveform that...
View ArticleForum Post: RE: ADS131B04-Q1: SPI Timing
I see this section about DRDY in the datasheet and I port the code that TI provide. But DRDY is always low until the data is ready. Do you know why is this happened and what I should do.
View ArticleForum Post: RE: ADS1286: ADS1286UL/2K5
not yet, here i want to express our troubles once again ; we found the current topside marking is ADS1286U for part ADS1286UL/2K5 of you shipped , then we checked your datasheet , and found it was...
View ArticleForum Post: DAC3482: PARITYP/PARITYN pins terminations when not using parity
Part Number: DAC3482 Tool/software: Hello, When not using parity, can PARITYP/PARITYN pins be floating? Best regards, K.Hirano
View ArticleForum Post: RE: DAC3482: PARITYP/PARITYN pins terminations when not using parity
Hirano-san, Yes, PARITYP/N can be floating when not being used. When this feature is not being used, the DAC3482 logic will not pay attention to it. Thank you.
View ArticleForum Post: RE: ADS1261: ADS1261 Reference voltage
Hi Bryan, thanks for pointing out the FSCAL-Register with 0xFFFF applying a gain of 4. I looked into it and found that i wrote: def calibrate ( self ): self.GANCAL() time.sleep(7) time . sleep ( 0.1 )...
View ArticleForum Post: TX7516: Full data sheet
Part Number: TX7516 Tool/software: How can I get full data sheet?
View ArticleForum Post: ADC12DL2500: Vih/voh/vil/vol
Part Number: ADC12DL2500 Tool/software: Hi, 1) Kindly confirm that the voh/vol from below table is valid for output signals only (SDO, CALSTAT, ORA0, ORA1, ORB0, ORB1) 2) And Input signals (SCLK, SDI,...
View ArticleForum Post: ADS7843: ADS7843
Part Number: ADS7843 Tool/software: Hello team, I am trying to identify the date code in marking on the following component: ADS7843 please advise.
View ArticleForum Post: RE: TI-JESD204-IP: I have not been granted access to the TI204c-IP
Hi David, I re-submitted the JESD204 Rapid Design IP Request Form to d-chaparro@ti.com . Regards, Antonio Dubovik
View ArticleForum Post: RE: ADS1286: ADS1286UL/2K5
Hello Zhang, Yes, I Understand the question you are asking. The letter "L" was removed from the topside of the device per the PCN I have sent over. If you notice in the PCN on the left side of the...
View ArticleForum Post: RE: ADS7038Q1EVM-PDK: Auto-Sequencing doesn't restart after...
Hi Deepak, Could you clarify if you are using the ADS7038-Q1 in an original design, or if you are using the ADS7038Q1EVM-PDK through the online GUI? If it is the second as per the thread is marked, I...
View ArticleForum Post: RE: ADS1299: Original waveform problem
Hi Jiahao, [quote userid="598300" url="~/support/data-converters-group/data-converters/f/data-converters-forum/1408578/ads1299-original-waveform-problem/5400266#5400266"]The band opens the BIAS, N...
View ArticleForum Post: RE: ADS124S08: 18 channel 3 wire RTD
Hi ABHAY VASHISTHA, See below for a possible implementation for 16x 3-wire RTDs using a low-side reference resistor and 2x IDACs. Basically you just need several multiplexers. Let me know if you have...
View ArticleForum Post: RE: ADS7038Q1EVM-PDK: Auto-Sequencing doesn't restart after...
Hi Joel, I am using the ADS7038Q1EVM-PDK with our own board. Not the motherboard provided with the kit. Therefore not using the online GUI. Thanks. Regards, Deepak
View ArticleForum Post: ADS1299EEGFE-PDK：ADS1299EEGFE-PDK
Part Number: ADS1299EEGFE-PDK Other Parts Discussed in Thread: ADS1299 Tool/software: Hi, I used channel 1 of ADS1299 to test a sine function I generated myself. The frequency of the sine function was...
View ArticleForum Post: RE: ADC12DJ5200-SP: CLK_P/N and SYSREF Input Waveforms
Hi Joseph, For these signals we typically AC couple them from a clocking chip and let the ADC self bias these pins to the correct voltage. Can you share which specs you are specifically concerned...
View ArticleForum Post: RE: ADC12D1600QML-SP: Inputs during Calibration Cycles
Hi Richard, No you do not have to disable the inputs to the ADC. Best, Eric
View ArticleForum Post: RE: ADC12D1600QML-SP: Inputs during Calibration Cycles
Hi Eric, Thank you very much! rich
View Article