Forum Post: RE: TAS5508C EQ GUI
Hi, Terry,This might help you:Use ALE5.2 and save it as cfg file in the below format and use the tool to download to the device. XYY ZZ ZZ … ZZ X – must have this character capitalizedYY – the...
View ArticleForum Post: RE: ADS1299, 4 electrodes, basic eeg, bias drive
Thank you very much, Andreas!Good luck in your search.
View ArticleForum Post: RE: PCM5122 DAC as I2S master troubles with PLL mode
Ok, GPIO3 (in) and GPIO6 (out) are good for methanksMarco
View ArticleForum Post: RE: Start Up Time and Input Signal Without Power Safety Questions
Hi, I do not think the device will be damaged from analog input and clock while power down. We sometimes leave the device in this situation but there has been no problem. I'll check this with test...
View ArticleForum Post: RE: bit duration in output code not correlated to CLK
Hi,sorry if i push again but this is a crucial point on this but can you please provide me some more details about?Thanks a lot.MR
View ArticleForum Post: RE: Possible to change product ID PCM2902?
PCM2xxx devices have their descriptors written at die level. They can only be changed with a silicon mask level change.We offer a modification service based on significant volume and NRE.You can...
View ArticleForum Post: RE: ADS1293 EVM programming
ADS1293EVM is not powered through JTAG. So when using with JTAG please connect the USB cable for power. Let us know if you still the issue after this. Thanks.
View ArticleForum Post: DAC5670EVM with FMC connector
Hi,One customer is asking whether the DAC5670 is available on an EVM which has an FMC connector? He wants to connect it to the ADC12D1800RFRB, which has an FMC connector at its output.Thanks!Marjorie
View ArticleForum Post: RE: ADC12D1600 default register values not as expected
Hi Marjorie,The clock is not applied until I manually enable it, well after power up. To double check, I removed the AC coupling caps on the clock inputs and powered the card again. Good thought...
View ArticleForum Post: RE: ADS1147 output drifting at Higher Temperatures
Hi Max,The baths we use are a type of oil, but I know there are other chemicals that can be used as well. It depends on the range of temperatures and how fast you want the bath to transition and...
View ArticleClik here to view.
Forum Post: RE: PCM9211 Configuration issue
Hi Sonu,I don't think this is related to the register settings, I have test it using AP SYS-2722, the frequency is very accurate with our EVM board. See below results:Have you followed the schematic I...
View ArticleClik here to view.
Forum Post: RE: ADS1241 Registers
Hi Bob,Please see the schematic bellow. I issue SELFOCAL at the top of my code, and use a 2.048 V as our reference voltage. Thank you for the point on differential vs. single ended measurement....
View ArticleForum Post: 1000 points FFT Audio compensation
Hi, My customer is working on a stereo home audio system and has an idea to add an fixed compensation circuit to it. They want to add a fixed 1000 or 1024 points FFT coefficients to the audio signal...
View ArticleForum Post: RE: Errors in AFE4490 datasheet
Hello Marko,I wanted to close the loop on this.The errors on the pinouts have been corrected in the datasheet.RegardsPraveen.If a post answers your question, please mark it with the "verify answer"...
View ArticleForum Post: RE: No power supply in box
Hi,I have send new address to you via message.thanks
View ArticleForum Post: RE: TVP7002 register settings for XGA RGsB input on DM6467T EVM
After following your advice and checking all TVP sync outputs and other status registers, I believe the TVP is configured properly for my input signal. All timings match the XGA DMT standard.I am...
View ArticleForum Post: RE: ADS131E08 opamp virtual ground issues
Please read my second comment, I retested with a 10k load and was getting higher that normal results
View ArticleForum Post: RE: Can I get the source code and schmatics of ADS8568EVM-PDK?
Hi. Tom.I downloaded the ads8568evm firmware from TI's FTP. ^^Is there much difference between MMB0 and MMB1?Thank you very much.
View ArticleForum Post: RE: Configuring AIC3204 for 8Khz Mono ADC and also DAC
yeah i am seeing the data in MSB is that desired ? and DSP format and i2s doesnt make any difference can you please refer any TI engineer who worked on speech codecs if possible at least on any codec
View Article