Quantcast
Channel: Data converters
Browsing all 89900 articles
Browse latest View live

Forum Post: ADC12DJ5200RF: JESD204 LINK from ADC12DJ5200RF Datasheet

Part Number: ADC12DJ5200RF I have two questions about ADC12DJ5200RF Datasheet Datasheet URL:...

View Article


Forum Post: ADC12DJ5200RF: Device clock calculation

Part Number: ADC12DJ5200RF Is the device clock A)4GHz under the following conditions? Or is it B)2GHz? For example, I want to transmit 12 bits of data per symbol at 4GSps. The sampling frequency is...

View Article


Forum Post: RE: DAC82001: Output noise (0.1 - 10Hz) graph

Hello Lucas-san, Thanks for your support. I will wait for your feedback. Best regards,

View Article

Forum Post: RE: ADS7830: Internal Voltage Reference Drop after I2C detect...

Hi Matt, So, you have to write the address and command byte. If all you do is write the address byte, the ADS7830 will assume your command was 0x00 and shut off the reference. In your multi-address...

View Article

Forum Post: RE: ADS131M02-Q1: Root cause of the offset issue

Hi Yoshikazu-san, I will look into the details and get it back to soon. Thanks&regards, Dale

View Article


Forum Post: TX7316: TR_EN Pin

Part Number: TX7316 Tool/software: Hello E2E Experts, Good day. I have a question about the TX7316 TR_EN pin. If I use on-chip beamforming, doesn't the level of the TR_EN* pin matter? Is it just the...

View Article

Forum Post: RE: ADS131M02-Q1: Root cause of the offset issue

Hi Yoshikazu-san, are the results mentioned in the Excel sheet with global-chop mode enabled or disabled? With global-chop mode disabled the ~200uV offset for the current shunt measurement would be...

View Article

Forum Post: RE: ADS1298: isolation protection circuit

Hi Ryan, I am not looking at isolate digital interface. As per IEC-60601-1 standard, need to provide isolation protection circuit for patient safety. Here, we have isolation from power supply and...

View Article


Forum Post: RE: TX7316: TR_EN Pin

Hi, In case of on-chip beamforming, the T/R switch turn on/off is controlled only by the internal digital based on the values programmed in the corresponding registers. The TR_EN* pins in on-chip...

View Article


Forum Post: RE: DAC43401-Q1: Want to know the right register for my situation

I tested 2 days ago changing SLEW_RATE from 0000 to 1111 and there's no change. test environment is repeating below chunk, changing 0xD1 value 0xC004 ~ 0xC1E4 yi2cset -f 9 0x48 0xD3 0x5208 w yi2cset...

View Article

Forum Post: AFE5808: Design support for AFE5808

Part Number: AFE5808 Tool/software: Hello TI team, I'm going to use this AFE5808 IC for my design but i need your help to design the circuit with this, So im using this with ABLIC 7502 chip so can i...

View Article

Forum Post: RE: ADS8326: ADS8326IDGKT

The first picture is the communication with the MCP: The second picture is the communication with the ADS: Number one: MISO line Number two: CLK line Number three: MOSI line The cs line is not present...

View Article

Forum Post: RE: ADS8686S: Bandwidth using Oversampling

Hi Cornelius Fink , I will get it back to you tomorrow, thanks. BR, Dale

View Article


Forum Post: DAC7311EVM: Where to download the drivers of MMB0 for windows 10...

Part Number: DAC7311EVM Other Parts Discussed in Thread: DAC7311 , DXP Tool/software: Where to download the drivers of MMB0 for windows 10 or above ? I used the MMB0 board with DAC7311 EVM,the evm had...

View Article

Forum Post: ADS8684: Interchannel interference

Part Number: ADS8684 hi team, my customer is afraid of the interchannel interference. Do we have some special ways to avoid this? thanks!

View Article


Forum Post: RE: DAC39RFS12: JESD204B/C Protocol for high-speed DAC and ADC...

Hi matt I am also considering purchasing a DAC39RF10 and am wondering which JESD mode would be best. I would like link too if possible. I am not sure about the "streams" item in Table 7-21. Is it like...

View Article

Forum Post: RE: ADS8684: Interchannel interference

Hi Zoey, Please review page 9 of the datasheet for crosstalk isolation and memory. Channel to channel isolation is 110dB typical.

View Article


Forum Post: ADS1298: Simulation of ADS1298

Part Number: ADS1298 Other Parts Discussed in Thread: OPA350 , TINA-TI Tool/software: We are working on an ECG project using ADS1298 from Texas Instruments as our analog front end module. So before...

View Article

Forum Post: RE: ADS131M04: N-pin voltage refers to communication issues

Hello: 2. We have conducted a series of checks and comparative tests, and we suspect that the jumping of those registers may be caused by over range. We will further verify this.—— We have tried, but...

View Article

Forum Post: RE: ADS131M02-Q1: Root cause of the offset issue

Hi Yoshikazu-san, it might also be good to verify that global-chop mode is really enabled. You could verify that by monitoring the DRDYn pin. The pin should transition low with a data rate which is...

View Article
Browsing all 89900 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>