Quantcast
Channel: Data converters
Browsing all 91339 articles
Browse latest View live
↧

Forum Post: RE: ADS8688: ADS8688 related issues

Throughput is based on the conversion and acquisition time, which are 850nS and 1150nS respective. The two add up to 2000nS or 500kSPS.

View Article


Forum Post: RE: ADS1292R: how to achieve pacemaker signal detection

Hello David, Thank you for your post. Please refer to TIDA-010005 . Regards, Ryan

View Article


Forum Post: RE: ADS8665: Driver code for ADS8665 and ADS8661

Hi Kai, Yes - if your driver for the ADS8665 works, then it should work for the ADS8661 as well.

View Article

Forum Post: RE: ADS7044: How to control ADS7044

The SPI convention is to read on the falling SCLK edge, but yes, the MSB should be valid after the 3rd rising clock edge.

View Article

Forum Post: RE: ADS54J69: ADC is not responding on SDout line

Hello, We are stuck on this! Can we please get some ideas/assistance as of what we can try?

View Article


Forum Post: RE: AFE5816: Problems in AFE output test pattern data

Hi, I believe this is FPGA related issue. Device should not behave like this . Device DCLK will be at 70MHz and you are sampling this in 280MHz ILA clock . Because of this resolution captured data...

View Article

Forum Post: RE: AFE5816: AFE output difference between test patterns.

Duplicate query , Closing this thread https://e2e.ti.com/support/data-converters-group/data-converters/f/data-converters-forum/1353879/afe5816-problems-in-afe-output-test-pattern-data

View Article

Forum Post: RE: ADC12DJ5200RF: Balun change

David, They can use the diff input with phased matched cables and an EVM of the balun they want to test. The board will need to be modified with R2, R6, R10,R14 needing to be uninstalled and...

View Article


Forum Post: RE: ADS1278: How to measure 5V Analog IN using ADS1278

Hi Bob Benjamin, Is there any update?

View Article


Forum Post: RE: DAC63204EVM: DAC63204EVM

Hi Katlynne, I am successfully able to run DAC in Voltage Output mode as I can see the voltage on OUT0 pin varying as per my data on input line. I am still not able to see data on SDO line, I am...

View Article

Forum Post: RE: ADS1274: DIGITAL VALUE GETTING IS INCORRECT WHEN MORE THAN 1...

Hi Keith Nicholas. Thanks for response, We have given 27MHz fclk, 0.5*f-CLK=13.5MHz minimum required. Our sclk is 27MHz. So it is sufficient to support 4 channels over a single DOUT pin. Now, we are...

View Article

Forum Post: RE: ADS7830: Internal Voltage Reference Drop after I2C detect...

Hi Tom, No more command was given, the reference is re-enabled automatically. Also, in this case, the internal reference can also be re-enabled, but they cannot accept this kind of quick and short...

View Article

Forum Post: RE: ADS7046: ADS7046 example C code with STM32

Unfortunately we don't know enough about your controller to tell you how to speed things up.

View Article


Forum Post: ADS124S08: Linux driver & example code

Part Number: ADS124S08 Other Parts Discussed in Thread: ADS1261 , I am looking at the ADS124S08 or the ADS1261 as alternatives to an AD7124. I would like to interface either ADC to a Raspberry PI (or...

View Article

Forum Post: ADS124S08: Data & Power isolator

Part Number: ADS124S08 Other Parts Discussed in Thread: ADS1261 , , ISOW7741 Hello, I need to use a galvanic isolator with the ADS124S08 or ADS1261, for both power and SPI. The ISOW7741 seems to be a...

View Article


Forum Post: RE: ADS1263: To measure 1uA to 15A DC current using ADS1263

Hi, Bryan Lizon86 Did you get a chance to look into the queries shared by my colleague?

View Article

Forum Post: DAC7551: Power up DIN before VDD

Part Number: DAC7551 Hello team, My customer wants to pull up Digital Input (SCLK, SDIN, SYNC) to 3.3V before VDD. So the power up sequence looks like below. But they are powering up DIN and IOVDD at...

View Article


Forum Post: RE: ADS124S08: Linux driver & example code

Hi Christian, The only example for Linux that I am aware of is for the ADS124S08: https://github.com/torvalds/linux/blob/master/drivers/iio/adc/ti-ads124s08.c There are a number of similarities...

View Article

Forum Post: RE: ADS124S08: ADS124S08IRHBR

Hi THESNI ASHRAF, Take a look a the Two-wire PT100 RTD Measurement Circuit with Low-Side Reference reference design. The low-side reference should be connected in a similar way. Best regards, Bob B

View Article

Forum Post: ADS8688EVM-PDK: GUI Installer

Part Number: ADS8688EVM-PDK I would like to download the GUI installer for the ADS8688EVM evaluation boards that I recently purchased from Digikey. I received the following message from your website...

View Article
Browsing all 91339 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>