Forum Post: RE: DAC161S997: DAC161S997 SPI issue
Hi Nikolay, I understand the concern but the first bit just indicates a read, so even if it was incorrect it is not important since the data and address would still be correct. This bit can simply be...
View ArticleForum Post: RE: ADS9224R: max sampling rate of ADS9224R
Hi Jerry, Thank you for your post. The ADS9224R and ADS9234R can both sample up to 3 MSPS simultaneously. The ADS9224R has 16-bit resolution and the ADS9234R has 14-bit resolution. The enhanced-SPI...
View ArticleForum Post: RE: Which DAC: I have the digital data on a csv file, I would...
Venkata, I have been out of office sick. Apologies for the delayed reply. More or less anything that lists DXP in the Tools & Software tab of the Product Folder is supported by DXP . From your list...
View ArticleForum Post: RE: ADS1248: Communication with ADS1248
Suraj, Here are a few quick hints that might help: - Make sure that START and /RESET are both high - The SPI is MODE 1, so that SCLK dwells low and the data is clocked in on the SCLK falling edge - /CS...
View ArticleForum Post: RE: Linux/ADS1278-EP: Code example needed for SPI
Christian, thanks for getting back to me with this. Unfortunately I could not find any source code after having installed the evaluation software. Maybe I clicked the wrong link? I used this one:...
View ArticleForum Post: RE: ADS1293EVM: ADS1293EVM interface to the MSP430 failure
Hello Alexander, I thought I updated it but tomorrow I will make it again for assurement. I have not got a board by myself now. Regarding my project. I would like to manage a single lead ECG which uses...
View ArticleForum Post: RE: Which DAC: I have the digital data on a csv file, I would...
Hi Kevin, Thanks for the reply. Hope you are doing well now! Are DAC8568 , DAC8718 and DAC8728 compatible with MMB0? I coudn't figure that out from the EVM user guide. Thanks, Venkata
View ArticleForum Post: RE: ADS1118EVM: Urgent: DOUT not responding to CS pin as expected
Maggie, If the EVM still works when connected to the normal TI software, the EVM board should work when connected to a separate microcontroller. Below is my setup. I soldered some pin headers onto the...
View ArticleForum Post: RE: ADS131E04: May Ads131 can replace AD9629?
Bogey, First, I'm sorry I didn't get back to you earlier. I'm not sure that the ADS131E04 work in the application because of the input range. I had mentioned the ADS131A04 earlier and that may work...
View ArticleForum Post: RE: SM73201-ARC-EV: RD 195 Safety Test Fail
Problem in the Safety Test was due to debug mode PSA_CRC calculations. Removed from the debug mode and worked like charm. Thanks for your help though, Ozino.
View ArticleForum Post: RE: TSW14J56EVM: Maximum data capture size
Hi Siavash, How are you? For your special case, we need to try it in our lab and see if we can capture such amount of data. One thing we can make sure is: when the TSW GUI runs, it would "display" data...
View ArticleForum Post: RE: LM98714: Longevity and newer device available?
Hi, LM98714 is active product and we are promoting to customers. Yes, good device to recommend. regards Shinya Morita
View ArticleForum Post: RE: TSW14J56EVM: Maximum data capture size
Hi Chen, Thank you! I greatly appreciate it. Best, Siavash
View ArticleForum Post: AMC1210: AMC1210 Reset Time
Part Number: AMC1210 Hi TI Support, I was wondering what the minimum time the RST pin on the AMC1210 needs to be held low in order for the AMC1210 to be reset? I have searched through the AMC1210 data...
View ArticleForum Post: RE: incorrect readings
Hi Michael, Would it be possible to see a schematic of the circuit? The only thing I can see from the register settings is that you are relying on the external ADC inputs, so it is possible the issue...
View ArticleForum Post: RE: ADS1281: How to calibrate ads1281?
Hi w w1, Welcome to the TI E2E Forums! Is the command sequence you showed what you are observing on the ADS1281EVM, or is that the command sequence you are currently using with the STM MCU? If you'd...
View ArticleForum Post: RE: DAC37J82EVM: Link establishment fails during ILA sequence
Branden, We have seen issues in the past when using Xilnix parts with serdes rate around 10Gbps. As a sanity check, can you try your setup with a serdes rate below 8 Gbps? What value are using for RBD?...
View ArticleForum Post: RE: SM73201-ARC-EV: RD 195 Safety Test Fail
Rahul, Great to hear that you fixed your issue. Thanks for sharing your findings. Regards, Ozino
View ArticleForum Post: RE: AMC1210: AMC1210 Reset Time
Hi Ben, Great question! One cycle of the system clock would do the trick in resetting the AMC1210 . We'll look into updating the datasheet with this detail on the next revision of the document.
View ArticleForum Post: ADS1247: Follow up on Calibration response to un-used ADC channels
Part Number: ADS1247 Hello, I have a follow up question pertaining to ADS1247 . In my application I have 5 channels for temperature measurement and each channel has an ADS1247 chip. I am using the...
View Article