Forum Post: RE: PCM1861,1863,1865 - some questions
Hi Dayfydd san,Thank you for your reply.Kind regards,Hirotaka Matsumoto
View ArticleForum Post: RE: TLV320AIC3262 ASI 4-channel using
J Arbona-san,The AS2 Data Output must be the same as AS1 Data Input signal. Why do the data not accord?Will the registers setting be wrong?best regards,Ito
View ArticleForum Post: RE: ADS1248 interfacing msp430g2553 using spi
Hi Bob, This is my schematic for RDT 100 - 3 wire I have designed base SBAA201 and I add 2 change analog input 4 - 20mA(Please visit the site to view this file)Please help me check.Question:1. What is...
View ArticleForum Post: PCM5102A Terminal Processing of Hardware Control Pin
HiIf we pull up(or pull down) pins of DEMP, FLT, FMT and XSMT, can these pins be connected to DVDD(or DGND) directly without resistors?Although our customer would like to remove these resistors, could...
View ArticleForum Post: RE: TLV320AIC3106 concurrent Multiple channel capture(record)
Understood.Thank you for the clear answer.Regards.
View ArticleForum Post: RE: TLV320AIC3262 ASI 4-channel using
J Arbona-san,Thank you for a reply.I appended to SystemSettingsCord your script.Now I am testing it.The signal pass of AS1 to AS2 is good, but a signal conflict occurred on DOUT1 pin.It may be a...
View ArticleForum Post: RE: AIC3256 BCLK and WCLK problem
Hi J-,Sorry for replying late, please go ahead with my 2 questions.As we are using our own custom board using OMAPL138 soc and connected AIC3256 device with it. We are booting from Linux OS and...
View ArticleForum Post: RE: ADS5232EV Power Connections
Armand,The PLL of the ADS5232 is enabled by default (shown in table on page 10). In order to not use the PLL with input clock rate less than 20MSPS, you will need to enable the serial interface by...
View ArticleForum Post: RE: DAC34SH84EVM GUI Software on Ubuntu
Basil,The current DAC348x software only supports Windows environment. We do not have a version supporting Ubuntu.-Kang
View ArticleForum Post: example codes for ADC12D1800
Hello, I’m going to use ADC12D1800 and want to find some example codes for FPGA interface. Can anyone tell me where to find such resources? Senmeis
View ArticleForum Post: RE: TSW1400 firmware for 2 wire 14 bit use of ADS6445
Richard, that sounds great. I will make sure I have the most recent release of the HSDCPro software. It would be great if you provide those ini files that support the 4 channels of 14bit 2wire mode...
View ArticleForum Post: RE: TVP 5158 register allocation
The oscillator does not prove anything other than the oscillator is working and the TVP is not in reset. It is, however, critical that the oscillator is running correctly before any I2C transactions...
View ArticleForum Post: RE: TSW1400+DAC34H84 Testing with High Speed Data Converter Pro
Kang,Thank you for your response. Thank you for showing me the errors in this setup. Before going further, allow me to explain my end goal. I am using this device to create a signal that has a...
View ArticleForum Post: RE: how to use ADS42LB49 full-range when the input is only positive
Hi Anil,AC couple the signal to the input of the single ended to differential converter. This will center your input signal at the input common mode of the single ended to differential converter so you...
View ArticleForum Post: RE: How to use motherboard MMB0 which ADS1298 plug into?
I sent you an email. :)Regards,
View ArticleForum Post: How to get start for SRC4392
Hi: Everyone , I have some trouble for SRC4392 code, pls help meNow I can config the src4392 , the reading data is the same as the writting ,but the src4392 no audio output. at all. i input the...
View ArticleForum Post: RE: DAC8581 tUPDAC timing
Hi Mark,It isn't necessarily impractical for you to use the DAC8581, we've just noticed some process shift over the lifetime of the part that can cause some issues in certain configurations. We are...
View ArticleClik here to view.
Forum Post: RE: Power supply for ADS5560 internal voltage reference
Kang，Thank you for your help!I have placed a 0.1uF decoupling capacitor on the VCM pin. However I found that the codes of digital output are up and down regularly ( as the yellow line shown in figure...
View Article