Forum Post: RE: Interfacing ADS54RF63 EVM and DAC34SH84 EVM with Xilinx...
Hi Richard, I went on to interface the ADS54RF63EVM board and DAC34SH84EVM board with a Xilinx Virtex 6 ML605 board.1. I am using the 19.2 MHz crystal source inside the DAC34SH84 to generate a 270 MHz...
View ArticleForum Post: Issues in interfacing ADS54RF63EVM and DAC34SH84EVM with Xilinx...
Hi, I went on to interface the ADS54RF63EVM board and DAC34SH84EVM board with a Xilinx Virtex 6 ML605 board.1. I am using the 19.2 MHz crystal source inside the DAC34SH84 to generate a 270 MHz clock...
View ArticleForum Post: ADS1274-EVM cannot be connected
Hi,I currently have the ADS1274-EVM and it's MMB0 motherboard. I'm trying to test it by using the software ADCPro, but USBStyx Driver cannot be installed to my PC (refer to ADCPro Hardware and Software...
View ArticleForum Post: RE: Help me! I can not install USBStyx Driver !!!
Hi Greg,I met the same problem which Khoi does ( http://e2e.ti.com/support/data_converters/precision_data_converters/f/73/t/335929.aspx ), and I tried the way you mentioned. Unfortunately, it still...
View ArticleForum Post: RE: LDC1000EVM question
Hi Hitheshi,I have asked one of my colleagues to address your question regarding LMP91300. If your last two questions are for LDC1000, the curve in the datasheet is for Rp only.To change the inductor,...
View ArticleForum Post: Problem reading and understanding values with ADS1299
Hi everybody.First of all, my native language isn't english, so, sorry about some mistakes.I'm using an ADS1299 to implement an EOG (electrooculogram) goggles. I'm using the ADS1299 with arduino pro...
View ArticleForum Post: RE: AFE7222 - external pull up resistance and pull down...
Hi Hirotaka,Vidl and Vidh are the maximum LVDS voltage swing.First consider the TX_CHA_PDN or TX_CHB_PDN register bits if they can serve the same purpose as the failsafe bias resistors. When these...
View ArticleForum Post: RE: TIPD151 reference design
HelloI have a problem opening the .sch & .pcb files of TIPD151 reference design with altium designer or altium designer viewer , please help .Can i use cadsoft eagle to open .sch (schematic) file ?...
View ArticleForum Post: problem in reading system monitor ADS1148
Hi, while reading the system monitor of ADS 1148, i am unable to read the correct default values of the device, instead i get a wrong default values, i am using the following electrical parameters AVDD...
View ArticleForum Post: RE: ADS8363EVM
Hi Tomaz,Unfortunately no. I do have some sample code for a few TI processors though that you might find useful. What controller are you planning to use in this project?
View ArticleForum Post: ADS8422 CAP1 and CAP2 pins connection
Hi,I'm using the ADS8422 in a design, and have a question about the circuit connection.It says on the data sheet about the CAP1 and CAP2 pins:"Decoupling of internally generated 3-V supply. Add 1-μF...
View ArticleForum Post: ADS8422 ADC nRD timing
Hi,In the ADS8422 ADC, can I tie the nRD pin to ground and just use the nCONVST to do the actual clocking?Does the nRD pin have to be clocked as well to shift out the data?I'm trying to minimize the...
View ArticleForum Post: RE: LDC1000EVM question
Hi,Please contact Tarig Chang (tchang@ti.com) concerning the LMP91300 eval board.Mike
View ArticleForum Post: RE: TLV320DAC23 - no audio out to headphones
Once again here is my setup code:// sendDACcmnd(0x1FFF); // reset sendDACcmnd(0x0180); // mute L line in sendDACcmnd(0x0380); // mute R line in// sendDACcmnd(0x05F9);...
View ArticleForum Post: RE: AFE7222 - external pull up resistance and pull down...
Hi Hirotaka,Mid code is when the MSB is high and all the other bits are zeros. For AFE7222, mid code is 0x800Thanks,Eben.
View ArticleForum Post: RE: Switching Gas Sensor Platform to Oxygen Mode (LMP91000)
Hello Will,Apologies for the delayed answere, we will get back to you within one day.
View ArticleForum Post: RE: LMP90098 and two RTD sensors - how to?
Hello,Apologies for the delayed answere, we will get back to you within one day.
View ArticleForum Post: RE: Why does LMP90100 give random results on the very first read?
Hello,Apologies for the delayed answer. We will look into this topic, and get back to you within two days.
View ArticleForum Post: RE: Can SMT Inductor be used with the LDC
Dear HitheshYes, un-shielded SMT inductors can be used with LDC1000. Please note that the sensing range is relatively closer with most SMT inductors.As for RFID, as long as the inductance is suitable,...
View ArticleForum Post: RE: First samples in datablock with Command : "06" with Firmware...
Greetings Torgeir,Thanks for this info. We are working on a fix. In the meantime, if you understand C, you can look in the firmware folder to see how data is being sent out. You can use command "11"...
View Article