Forum Post: RE: ADC34J45EVM: with Arria 10 SOC evaluation board
Hi Ken, Unfortunly I don't have TSW14J56. I will try the registers as you suggested and I will update you.
View ArticleForum Post: RE: LM4546B: LM4546B WES7 Driver Question
Hi, Richard, All the AC 97 codecs seem to be obsolete now. There's no much information about this. Please take a look at this e2e thread for details: e2e.ti.com/.../177086 Best regards, Luis Fernando...
View ArticleForum Post: RE: ADS131E06: What is pin capacitance on DOUT, SCLK, CS, DIN for...
Hi Dave - I think you meant to attach an image, but I don't see it. Remember to include SCLK as well.
View ArticleForum Post: RE: ADCPRO download link help
Brynn, I'm glad you were able to find that. On some of our other EVMs, ADCPro will give you an error message when external supplies aren't provided. If you have any other questions, please post back....
View ArticleForum Post: RE: TSW14J56EVM: TIMED_OUT_ERROR connecting to ADC14x250EVM
Hi John, I tried the steps in the UG and get the same results you did. I think the clock output from LMK is not set correctly. I'm working on it and will update you. Regards, satish.
View ArticleForum Post: RE: ADS1675REF Source file problem and plugin
This question has been answered in a different post: e2e.ti.com/.../240859 Joseph Wu
View ArticleForum Post: RE: ADC12D1600QML-SP: Absolute maximum ratings
Hello Steve, The ADC12D1600QML datasheet is in the middle of a rewrite to clarify the abs max and operating limits. It will look like the tables in the ADC12D1620QML-SP datasheet....
View ArticleForum Post: RE: ADC32RF45: FFT response, unidentified spurs
Hi Richard, Thank you for the details. A couple of additional questions regarding the Interleave spurs in particular: Are the IL spurs single tones or do they follow the input (frequency wise)? If the...
View ArticleForum Post: RE: ADS124S08EVM: Drifting signals
Hi Michael, If the excitation and reference are the same voltage source, then you should not see the drift of the source within the measurement. This assumes that the components do not drift. We often...
View ArticleForum Post: RE: ADS1248: ADS1248 single ended measurement
Daniel, Basically you could do this type of a measurement but there are some issues to keep in mind. There is some error from the REF3030 which would offset the 1.5V that you're setting up with the...
View ArticleForum Post: RE: ADC32RF45: Slow Speed En 2 setting in Power_Analog_Config.cfg
Hi, I do not have the list of edits that are queued up for the next rev of the ADC32Rf45 datasheet. I do know that the datasheet for the lower speed grade ADC32RF44 was released three months later and...
View ArticleForum Post: RE: ADS54J54: Difficulty getting code group synchronization and...
Hi, I spoke with the person who generated some of the first config files for the EVMs using the LMK04828 with our JESD204b dataconverters, and that section of LMK configuration in lines 111 to 123 were...
View ArticleForum Post: RE: ADC32RF45: Slow Speed En 2 setting in Power_Analog_Config.cfg
Richard, Thanks for your reply. I am using the latest version of the SPI GUI with the EVM. Both channels are in Nyquist zone 2 when we are seeing the performance difference, and I am setting the...
View ArticleForum Post: RE: ADC32RF45: FFT response, unidentified spurs
Hi, In that figure4 of the datasheet the input is a single tone, and so the spurs are single tones. But if the input were a modulated signal of some width, then these same spurs that are a function of...
View ArticleForum Post: RE: ADS8681EVM-PDK: ADS8681EVM-PDK
We do not have a simple converter board for the fine pitch connector. Attached is a picture that may help. You will have to connect wires on the point where the resistors are removed. This is just a...
View ArticleForum Post: RE: ADS1220: Problem in Thermocouple and RTD signal transmitter...
Hi Mahmoud, Welcome to the forum! I will make a few assumptions and you can correct me if I'm wrong. You want to use two TCs or one 3-wire RTD using the same circuit with no jumpers or switches. You...
View ArticleForum Post: RE: ADC32RF45: Slow Speed En 2 setting in Power_Analog_Config.cfg
Hi, No more changes that I know of. There are different configuration files for trim for the different Nyquist zones, but if you are using the Quick Setup tab of the SPI GUI and choosing the Nyquist...
View ArticleForum Post: RE: Asking for the ADC recommendation for digital mic in and line in
Hi Diego, Thanks for help. Could you let me know how to set register 12 for the customer user case? For DOUT1 and DOUT2, it seem the same data. How to map the line-in/digital mic input and the data...
View ArticleForum Post: ADS1299: ADS1299 how to pass the Polarization voltage of 300mV.
Part Number: ADS1299 ADS1299 how to pass the Polarization voltage of 300mV? 1.sofortware:? 2.hardware:?
View ArticleForum Post: RE: PGA411Q1EVM: Why does PGA411-Q1 angle and velocity readout...
Markus, Can you check your SPI frames on the oscilloscope? I also recommend turning off the continuous device CRC check for now, especially if you are getting CRC errors in your SPI frames (Jon...
View Article