Forum Post: RE: Relation between SCLK and Sampling clock in ADC128S102
Hello,The ADC128S102QML is tested for the entire range of 50ksps to 1Msps (0.8MHz to 16MHz clock). The ADC128S102 is tested for the range of 500ksps to 1Msps (8MHz to 16MHz). It will work down to...
View ArticleForum Post: RE: AIC3204 DAC problem
Hi Zarar,I would start with looking at the document that Don has mentioned.Do you have an EVM? I would try to test your configuration on our EVM to see if you get the same results.Regards,~John
View ArticleClik here to view.
Forum Post: RE: TAS 5760LD after power on : first write I2C command will not...
Hi Paul,"The first wright I2C command will not deliver a acknowledge, only when first there is a 'read device' executed then the first write I2C command will deliver a acknowledge."Do you mean if the...
View ArticleForum Post: RE: User programmable filters in AIC3204 to filter DC offset, Help!
Hi Sergio,Great to hear you got things working!Regards,J-
View ArticleForum Post: RE: LMP91300 - supported by SPIO-4?
Hello,Yes, there is a LMP91300 eval board. It uses a special communication board (not the SPIO-4 board) to talk to the computer. The LMP91300 was made to be used in inductive proximity sensors. The...
View ArticleForum Post: RE: Reading multiple ADC121C021 high speed I2C AD Converter read out
Hi Harm Lok,Sorry for the delay. I was researching the design documentation.IN principle I don't see anything wrong that you are doing. To enter the High Speed mode (Hs) you ned to send out the master...
View ArticleForum Post: ADS8363: CONVST relative to CLOCK
The ADS8363 has a specified setup time, t1, for CONVST to CLOCK. As far as I can see, meeting this spec is mandatory. If this is so, then it is not possible to capture the source signals on an...
View ArticleForum Post: RE: Interfacing TVP5150 with TI Piccolo and computer
Another thing, my piccolo has a 90 MHz clock.. shouldn't this be enough computing power to handle all of this? I can have 12 pins into it and 12 pins out of it in to the parallel FTDI chip. This is...
View ArticleForum Post: AIC23 ADC I2S
I have a software processor running on an FPGA connected to a TI AIC23 audio codec through a daughtercard. The audio codec is in master mode and generating the lrcin/blck signals that I need to grab...
View ArticleForum Post: RE: Measuring angle using LDC1000
Hello Stefan,A few things you can do:Using inductance data along with moving average filter of 100 points seem to get you there.Also, if you decrease the frequency of LC tank by a factor of 10, that...
View ArticleForum Post: RE: Measurement of Rp
Hello,Regarding Rp - do you have an access to another EVM? If yes, please take Rp measurement to compare the results.
View ArticleForum Post: RE: Human body - any guideline?
Yes, it can be (and have been) done.Let me check with the legal if I can post the solution on the public forum.
View ArticleForum Post: RE: PCB coil
Hello DJ,I'm sorry, what PCB coil are you referring to?PCB coils are usually cheaper than wound inductor.We have no plans of supporting wound inductors because they come in all sizes and shapes. We...
View ArticleForum Post: RE: need help: gear tooth counting
The LC tank always oscillate at the resonant frequency. Eddy currents will change the inductance of the system, and thus, resonant frequency.
View ArticleForum Post: RE: AIC3204 DAC problem
No John i don't have an EVM, if you check my configurations on an EVM that would be a great help indeed. Thanks
View ArticleForum Post: RE: Vehicle Loop Detectors
2014 HYUNDAI SANTAFE Car Special Version 2.4 include gasoline demand driven and Oil Machine 2 2.2 1 drive to use automatic transmission 6-speed semi-automatic . is imported CBU from Korea to changing...
View ArticleForum Post: RE: capacitive load stability of AMC7812 DAC part
Hi Matt As you have said, 10nF is refer to the max capacitive load. So I do not understand why in the datasheet 10nF is written in the 'min' column?Thanks!
View ArticleForum Post: AN099 and changing codec from AIC3104 to 3204
I would like to upgrade the codec in AN099 from the 3104 to the 3204. Has anyone done this, and what are the hurdles? It appears that the 3204 has a much higher degree of configurability, and therefore...
View ArticleForum Post: RE: need help: gear tooth counting
Hello Sir,I am lucky to get support from you sir...Is that coil should be energized with alternating current sir but ldc1000 is of working with dc supply...can you explain sir????
View ArticleForum Post: ADS1247 calibration question. PGA accuracy question.
Hello, I'm about to use ADS1247 to read a shunt resistor.Normally the ADC will be used with the PGA gain of 16.This shunt can read ranges of up to 50A and has a resistance of 2mOhm. I have access to a...
View Article