Forum Post: RE: DAC7750: why are there two TVS diodes?
The above artical say that for non-symmetrical supply voltages two unidirectional TVS diodes must be used. I cann't understand why can a bidirectional TVS diode not used for non-symmetrical. Coud you...
View ArticleForum Post: RE: DAC3283EVM: DAC3283 Communications
Ok, so I loaded your latest register values and enabled the FIFO. The distortion should disappear when you disable the Clock Divider Sync. This should only be enabled at startup and then disabled, or...
View ArticleForum Post: PCM2707C: Why does headphone jack stop working when pin 9 is...
Part Number: PCM2707C Posting on behalf of customer: "Why does the PCM2707 turn off the headphone jack when I2S output mode is enabled? On the PCM2707C when you pull up pin 9 (FSEL) you are in SP/DIF...
View ArticleForum Post: RE: ADC12J4000EVM: Help to parse ADC12J4000EVM data stream
Jim thanks for the clarification. Regards, Bing
View ArticleForum Post: RE: TLV320AIC3263: Program TLV320AIC3263 without evaluation board...
Hey Luis, Thanks for the info, But to detect when someone says OK Google or hey Siri we need use a full fledge DSP right ? Regards Shashank
View ArticleForum Post: RE: ADS54J60: ADS54J60 wrong behaviour when clipping
Patrice, These are the files I am using and the same versions of GUI's. Did you press the reset switch on the ADC EVM after loading the LMK config file? If so, you may have a bad EVM. Send me your...
View ArticleForum Post: RE: ADS5474EVM: Interface between TMS320C6472 and ADS5474EVM
Dear Richard, Thanks for your response.
View ArticleForum Post: RE: ADC32RF45: The settings of emphasis in DATASHEET(Real) and...
Hi, I understand that In Table68 of adc32rf45 datasheet, 0/1/3/7/15/31/63 values are for register setting and 0/-1/-2/4.1/-6.2/-8.2/-11.5dB are matched to 0~6 AMI setting value in order. Thank you so...
View ArticleForum Post: RE: ADS124S08: How to measure four 3-wire RTDs
Dear Joachim, Thanks a lot for your quick answer. I understand the solution number 1 with 2 x ADS124S06 and the solution number 2 with one ADS124S08 plus one external 2x 1:4 MUX. (sorry I called this...
View ArticleForum Post: RE: PCM2912A: Does the PCM2912A Support USB Audio 2.0 Specification
Thank you for your reply. Diego. for confusing. We are asking about the USB Audio Class 2.0 specification. Is the PCM2912A compatible with it? Best regards, Wayne Chen 01/04/2017
View ArticleForum Post: RE: TLV320AIC3120: Need Audio Driver Code for Merging CC2650...
Hi Luis, thanks for the help. Can you please tell me if you have the Driver Code for the Audio Codec IC and CC2650 Controller? What are the other dependencies required ? Regards, Parveen
View ArticleForum Post: RE: Can ADS54J66EVM interface with ZC706 Dev-board correctly?
I am try to follow your first suggestion. But have a little confusion: 1. What's meaning of simply modify the provided firmware to have the JESD204 IP output data routed to your signal processing logic...
View ArticleForum Post: RE: ADS124S08: How to measure four 3-wire RTDs
Hi Philippe, let me know if the following clarifies things: 1) The schematic drawing above might be a little misleading, because I do not show the lead resistances of the RTDs. Following is a new...
View ArticleForum Post: RE: ADS124S08: How to measure four 3-wire RTDs
Hi Joachim, I am sorry but I continue to not understand why you need 2 MUXs. I miss something for sure, I will try to make a drawing tomorrow. About the thermocouple solution, what is the maximum...
View ArticleForum Post: RE: ADS124S08: How to measure four 3-wire RTDs
Hi Philippe, my apologies. I am waiting for your drawing then. Maybe you even have a smarter solution to implement the measurement. I am always interested in learning news ways. You could measure up to...
View ArticleForum Post: RE: ADS5560: Single ended input
Thanks for your support. Another issue is that I try to use existed Launchxl-F28377 processing digital signals from ADS5560 . I have to check and consult Microcontroller section.
View ArticleForum Post: ADS1255: First sample read after RDATAC is wrong (sometimes)
Part Number: ADS1255 I am collecting data in RDATAC mode. At the end of the acquisition I send an SDATAC command. I am monitoring the CS, CLK SDIN and SDOUT lines with a Logic Analyzer, and I can...
View ArticleForum Post: DAC7760: Connect to Launchxl-F28377S
Part Number: DAC7760 I'm preparing the analog out test based on Slau519 and try to use existed Launchxl-F28377S but its most of pins have been occupied. Do you have experiences to handle this issue?...
View ArticleForum Post: ADS1298R: How to make the defibrillator protection circuits for...
Hi TI experts, I've looked through all the posts on defibrillator protection circuits in the forum. The SPARB36B.pdf and...
View ArticleForum Post: RE: ADS127L01EVM: Digital Pins and Reference Capacitors
Hey Ryan, Regarding the pins, this could be a misunderstanding on my part due to misreading the datasheet or being a novice. However, I am referring to both Hardware Mode Pins and pin8 INTLDO the...
View Article