Forum Post: RE: Unable to get ADS1298 to connect to computer via USB
Mr Piel -The software will work OK; the problem that we have seen is actually the driver installation. You should receive an email with some further information shortly.
View ArticleForum Post: RE: Spring as inductive sensor
Insulating the spring makes perfect sense if the adjacent windings touch each other - there is direct current path, so there is no coil!Mechanical solution (crimping/clamping) can be used as an...
View ArticleForum Post: RE: PCM2900 and PCM2900C comparison for USB1.1 and USB2.0...
Hello Peter,PCM2900C was created to meet Microsoft Windows Logo for compatibility with Windows 7. Main difference is changed volume characteristics. There are also changed USB descriptors. It is...
View ArticleForum Post: RE: ADS1675 internal input buffering
The ADS1675 requires external buffer for specified performance. Please review the Application Information item #6 and Figures 54/55 in the datasheet.
View ArticleForum Post: RE: ADS130E08 Sample Code
We do not have any sample code for the ADS130E08. You should receive an email that contains information on the ADS131E08EVM-PDK source that you may find useful and can reference for your development...
View ArticleForum Post: RE: About the Linux driver of TLV320AIC3204.
Dear D.Harti-sanThank you for the reply.What is necessary is just to download the driver of an AIC325x family, when using AIC3204.Best regards,Satoshi
View ArticleForum Post: RE: hii need a help
Hello Madhu,for gear tooth counting, there are two rules of thumb to achieve best performance:To detect the conductive target reliably, the physical size of the inductor should not exceed the size of...
View ArticleForum Post: RE: Using the LDC 1000 for presence detection of large objects
Hello, Deep apologies for such a delayed answer.Yes, LDC will be a perfect ft for this application. It is based on the same physical phenomenon of detecting changes in the magnetic field, generated by...
View ArticleForum Post: RE: metal targets minimum dimensions
Hello Francisco,Deep apologies for such a delayed answer.The rule of thumb is that the objects have to be comparable bigger than the skin depth (please look up its formula!)You can easily decrease skin...
View ArticleForum Post: RE: LDC Design Flow
Hello,Could you please elaborate on your question?A good place to start is here: http://webench.ti.com/webench5/ldc/?lang_chosen=en_US
View ArticleForum Post: RE: One question about TI's DS90C387R and display controller...
Thanks for your reply. I didn't find any configuration for the source. Could you give me some ideas about how to configure the parallel 24 bit RGB output (R[7:0], B[7:0], C[7:0]) in DDR...
View ArticleForum Post: RE: Design for 12 pcb aerials
Hello Jonathan,Can you provide more details, otherwise it's quite obscure...for 5kS/s I would stay away from multiplexing until the proof of concept is done. Afterwards, it might be possible to...
View ArticleForum Post: RE: Buffer OP for ADS1672 / ADS1675
The ths4521 part makes sense with the ADS1675. However, the eval board uses THS4503! This makes no sense to me at all. The harmonics of THS4503 are only ~75 dBc, which is well over the SFDR of the...
View ArticleForum Post: RE: How can I change temperature configuration register of the...
Howdy Seung Joon Lee,Welcome to the e2e forums! That is an interesting issue, as the temperature configuration register should change with the SPI write operation. Is it possible for you to send an...
View ArticleForum Post: RE: DAC8822 update rate
Hello, Thank you for your prompt reply.I understood. Best Regards,Ryuji Asaka
View ArticleForum Post: RE: vga output from am335x interfaced with 8200
OK, so I think you have found the issue :)How are you configuring the THS8200? Is it slave or master timing?Are the H & v outputs from the processor correct?Are you using discrete syncs or embedded...
View ArticleForum Post: RE: Buffer OP for ADS1672 / ADS1675
Keep in mind that the most of the specs for the THS4503 are for frequencies much higher than the bandwidth of the ADC.That said, you are welcome to use whatever op-amp that you might think fits your...
View ArticleForum Post: RE: Inquiry regarding shutdown mode on ADC081S021
Hello there,The SPI bus transaction you have shown in your posting will result in the ADC081S021 entering the SHUT-DOWN.In your example the CS goes High after only 2nd falling edge of SCLK. Once the CS...
View ArticleForum Post: RE: ADS131E04 Input Information Needed
What are your concerns/requirements?The ADS131E04 can accept input range is +/- Vref/Gain (see datasheet Electrical Characteristics), so you input signal should be OK. You can even set the gain to...
View Article