Forum Post: metal targets minimum dimensions
Dear TII'd like to know what are metal target minimum dimensions that can be sensedby LDC 1000; again if pin like metallic objects with centimetric lenghtand sub millimetric diameter can be sensed...
View ArticleForum Post: RE: details of USB-CDC connection requested
Hi Dmitirii,You do not need a USB analyzer if you can understand the MATLAB or LabView libraries, which not only show typical usage scenarios but also expose all the commands.Thanks,
View ArticleForum Post: RE: ADS1675 series resistors in all digital inputs
Mike - The resistors in series with the lines are strictly for damping purposes since some of the signals are high frequency and this helps slow down the edges a little and prevent ringing on the lines.
View ArticleForum Post: RE: ADS1602IPFBR PIN handling
Greg-Hupp sanThankyou for taking afollow-upof the respondents.I was very helpful.Iexcuse memissmydatasheet. Best regard.BEN.
View ArticleClik here to view.
Forum Post: RE: 2 questions about ADS131E08
The spec for AVSS to DGND was removed in error on the previous revision of the datasheet.There will be a datasheet update that should be available tomorrow and will have this spec restored. I will...
View ArticleForum Post: ADS1299EEG-FE electodes
does ADS1299EEG-FE Kit comes with electrodes cap or i have to buy them separately and if they come separately not with kit which one /from whom should i buy those electrode? how many electrodes...
View ArticleForum Post: RE: How to read ADC value from LMP90080
Hello,I think you are running into the noise floor of the LMP90080 by setting VREF so low. As VREF is reduced, the range of acceptable analog input voltages is also reduced. Reducing the value of...
View ArticleForum Post: RE: Power Consumption / Better recommendation of TLV320xxx
The 180mA looks like a typo. The standby current is in the uA range regardless of 1.8V vs. 3.3V (what app note and page did you find this number?) The AIC3263 (like the AIC3254&6) is very flexible...
View ArticleForum Post: RE: Audio DACs: Cheap and reliable generation of FS/LRCK from...
Matthias,The solution of using the SPI port with a counter to generate the L/RCLK should work. You need to make sure you can align the L/R clock with the data using the reset pin in the application...
View ArticleClik here to view.
Forum Post: RE: ADS1298 Single-Ended Input Range
Hi Nate,Thanks for your question. The short answer is that 0.45 V to 2.85 V is a perfectly acceptable range for a 3.3 V supply and VREF = 2.4 V (I'm assuming single-supply? AVDD = 3.3 V, AVSS =...
View ArticleClik here to view.
Forum Post: RE: AMC7812 can't i2c bus how use it? example code..
Hi Roberto,Thank you for the post. As you suspected, I did not receive any email regarding the question. I've tried to recreate the problem in the lab, but unfortunately wasn't able to. I've included...
View ArticleForum Post: RE: SD16 makes a good random number-generator - question for SD16...
Hi llmars,That is correct. The primary difference is that the SD16, SD24, ADC10 and ADC12 converters found in the MSP430 family of controllers are built in a digital process, while precision...
View ArticleForum Post: DAC7311 - are inputs 3.3V tolerant when Avdd is 2.5V?
I could not find anything in the datasheet regarding this DAC having input protection diodes.I have Avdd at 2.5V (from a voltage reference) and would like to drive SYNC, SCLK, DIN with 3.3V signals...
View ArticleForum Post: RE: Representing captured data in sine wave form
Hi SyedUnfortunately we don't really have much support for the software side of things, especially on the Wavevision tools. You might be able to find what you're looking for in a few other threads...
View ArticleForum Post: RE: ADS7954 / Manual Channel Sequencing Mode
Hello Sandeep san, Thank you for the reply.I understood. Best Regards,Ryuji Asaka
View ArticleForum Post: RE: LM97600 / LVDS input, output characteristics
Hello, Could you please kinldy let me know this answer ? Our customer using 2GHz LVDS clock which generated by LMK04803 for LM97600.LMK04803 VOD at 2GHz is 250mV.If LM97600 VID is 400mV pp, we may not...
View ArticleForum Post: ADS1298ECG-FE
Hello,I use front-end (FE) broad with ADS1298ECG-FE program to measure ECG. but i have problem when i measurement, I can't measure more than 10 minute (10 minute = 1800000 simple per second). because...
View ArticleForum Post: RE: LMP90100
Thank you Both for help .Do you suggest any way for the protection of the PT100 lines ? and EMI/ EMC filters ? I asked this because our application is automotive , so we should protect the inputs of...
View ArticleForum Post: RE: lmp90100 layout
Hi,Thank you for your reply. I'll be very glad if you can send gerber files for LMP90100.Davor
View Article