Quantcast
Channel: Data converters
Browsing all 90237 articles
Browse latest View live

Forum Post: RE: ADS7852: ADS7852

Hi Rajashekhar, Welcome to our e2e forum! The digital I/O levels listed in the table on page 3 of the ADS7852 datasheet show 3.0V as the minimum input high level, so the 2.6VOH of the TXCO may not...

View Article


Forum Post: RE: ADS8341: ADC Error with External vs Internal Clock

I tried that as well. There is no change in the output. Is the clock pattern correct? Old uC is 8 bit and new one is 32 bit. Is that making any difference?

View Article


Forum Post: RE: TSW14J57EVM: TSW14J56EVM replacement

Hi John, We are pushing older TSW14J56/7 fpga cards to the TSW14J59EVM. Firmware for the J59 would be developed through TI-JESD204-IP request for the specific DAC mode and class of AMD FPGA. Thanks,...

View Article

Forum Post: RE: DAC39RF10-SP: Inquiry on how to apply code carrier coherence

JH, We are verifying with our Global Trade Compliance team how we should handle requests coming through a distributor since this device is export controlled. We should have an answer early this week....

View Article

Forum Post: RE: TSW14J57EVM: TSW14J56EVM replacement

Hi Chase, Will the TSW14J59EVM be fully compatible with the DAC39J84EVM and DAC38RF82EVM for use with HSDC Pro ? Are there any known limitations or issues with using the TSW14J59EVM to control these...

View Article


Forum Post: RE: TSW14J57EVM: TSW14J56EVM replacement

The J59 will not work with HSDC Pro. you have to submit IP request and use vivado for control. Hardware wise there may not be 1:1 connections over the FMC connector since J59 does not route all HPIO...

View Article

Forum Post: RE: ADS1298: DRDY pin not going low although the other functions...

Hello Khoi, Are you using internal or external clock mode? Only R65 or R60 should be installed, but not both. If you are using external clock mode (OSC1), install R65 and remove R60. If using internal...

View Article

Forum Post: AFE4900: afe4500

Part Number: AFE4900 Other Parts Discussed in Thread: AFE4500 Tool/software: Mauser is showing the afe4500 product as obsolete. I am building a medical device. How long will this IC be avqilable?...

View Article


Forum Post: RE: ADS1299-4: About resistance measurement function (LOFF(AC))

Average of the received signal amplitude (Vp) should be ok for calculating the impedance. Regards, Ryan

View Article


Forum Post: RE: ADS1299-4: [Config Support]ADS1299-4 SRBx, BIASx pin...

Hello - please refer to our device data sheet and ADS1299EEGFE-PDK User Guide for recommendations on electrode connections, specifically for bias and reference electrodes. Regards, Ryan

View Article

Forum Post: ADS1261: System cycle time calculation at 40k ODR

Part Number: ADS1261 Tool/software: Hi, I am using an ADS1261 designing a force plate with four loadcells, my object is sampling the sensor at 1000hz, according to ads1261's datasheet tab8 and...

View Article

Forum Post: RE: ADS1299: Channel Crosstalk in μA Excitation for Lead‑Off...

Hello Divya, Please excuse the delay in my response as I was out of office for several days in the past two weeks. The ADS1299 current sources have only a typical ±20% tolerance. Therefore,...

View Article

Forum Post: RE: ADS131M06-Q1: ads131m02

Hi peter, You did not answer my question, where is your input clock to the ADC (pin 23 - XTAL1/CLKIN)? Your schematic does not show it. In your first timing, the /SYNC from your microcontroller was...

View Article


Forum Post: RE: AFE4900: afe4500

Hi Marc, Thanks for the question. The AFE4500 is not obsolete but is now a custom device. It will continue to be available but the purchasing method has changed. I will email you offline to discuss...

View Article

Forum Post: RE: ADS1261: System cycle time calculation at 40k ODR

Hi zhaojia, I am not sure where the factor of 2 comes into the equation, unless you are planning on taking 3x measurements per load cell: the first measurement completes in 179us, while the other two...

View Article


Forum Post: RE: AFE882H1EVM: EVM application usage

Doudu, Can you take a picture of the EVM to show the jumper connections? It may help me debug the output. Do you have the +15V and -15V supplies connected? Joseph Wu

View Article

Forum Post: RE: SN54SC8T541-SEP: Is the Output Current Limit in...

Hello Dhir, Current mentioned on the datasheet is per pin. Regards, Josh

View Article


Forum Post: AFE532A3WEVM: HELP on SMART-DAC-EVM-GUI

Part Number: AFE532A3WEVM Tool/software: After installation on my Window 11 computer, and run Smart-DAC-EVM-GUI, show following error. Error 1003 occurred at Invoke Node in SmartDAC.lvlib:Startup...

View Article

Forum Post: RE: AFE11612-SEP: Queries Regarding ADC Reference, ENOB, AVcc,...

Hi Dhir, These are per I/O pin. I'll talk with a designer about the sequencing issue since the datasheet doesn't specify what could happen. They may be able to run simulations to give a better idea....

View Article

Forum Post: RE: AMC131M03-Q1: ads131m04

Hi Srinath, If the device is configured for 24 bit mode, all the words will be in 24 bit format. For the 3 ADC values, it will be a full 24 bit adc data value. For the other words (response and crc),...

View Article
Browsing all 90237 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>