Quantcast
Channel: Data converters
Browsing all 90415 articles
Browse latest View live

Forum Post: RE: DAC8775: DAC Voltage output frequency response

Veselin, The CCOMP does not go to the inverting input of the op-amp. Instead, this capacitance goes to the goes to the input of the output stage of the op-amp. This is basically a miller compensation...

View Article


Forum Post: RE: ADS8168: Whether support input Simultaneous Sampling ADC?

Hi Tom, ADS8588S is 12 bit. Customer need 16 bits, 8 channels, Simultaneous Sampling>800ksps, data output in parallel interface. I have recommended ADS127L18IRSHR. Do you have better suggestion?

View Article


Forum Post: RE: AFE58JD18EVM: HMC_DAQ GUI - Device Communication Error

Hi, Can you please try opening the device gui directly ? If I understand correctly you have AFE58JD18 EVM and your own capture card. You want to do the device configuration using our GUI and then...

View Article

Forum Post: ADS9219: Initialization Sequence and Normal Operation Mode | Run...

Part Number: ADS9219 Tool/software: Hello, I will design a new application for the ADS9219 and for me it is not clear if I need to run the initialization sequence after power up or not? Even if I want...

View Article

Forum Post: TX7316EVM: STL/STEP files

Part Number: TX7316EVM Tool/software: I do not know if this is a relevant question for this forum, but is there any STL/STEP files for the TX7316EVM available? Cannot seem to find it on the website...

View Article


Forum Post: RE: DAC8742H: Does DAC8742H has passed the physical layer test of...

Thong, Normally, we're blocked on our network from dropbox, but I was able to get an exception. I was able to download the two csv files, and the pdf figure, However, I'm still blocked from your zip...

View Article

Forum Post: ADC124S021: How should unused input pins be handled?

Part Number: ADC124S021 Tool/software: What should I do with the input pins that are not in use? Are they open? Connected to ground? Pulled up to power?

View Article

Forum Post: AFE4960P: 1 ch ECG (only 2 electrodes) + Res + PPG Mode...

Part Number: AFE4960P Tool/software: Hi, We are developing a device that requires acquiring a single-channel ECG signal using only two electrodes, along with respiratory and PPG data. However, we are...

View Article


Forum Post: RE: ADS131E08: How to Suppress Industrial Frequency Noise in...

Thank you for your reply, we troubleshooted and found that it came from the power supply, after changing the supply frequency to 60hz, the harmonic frequency became an odd multiple of 60hz, the...

View Article


Forum Post: VSP5612: Cross AD9977BBCZ

Part Number: VSP5612 Tool/software: Hi team, Our cross tool does not have a cross for AD9977 Datasheet and Product Info | Analog Devices What is our best cross and what are our pro's? Thank you. Kind...

View Article

Forum Post: DAC53004W: VCC Power supply voltage range

Part Number: DAC53004W Tool/software: Hi TI team, I have some queries regarding DAC53004W. Please check below. Q1. May we utilize a 24V power source for the VCC connection? As per the datasheet, Vref...

View Article

Forum Post: DAC60502: DAC60502DRXR

Part Number: DAC60502 Tool/software: Can you please provide technical support to calculate DAC total output error and Dac noise error for the part number DAC60502DRXR .Also please provide any...

View Article

Forum Post: RE: TSC2200: Failed to read VBAT, VBAT 2, AUX1 and AUX 2 voltage...

Apologies for the delay, we are out of office for US holiday. Mir will update this thread within a couple of days. Thanks for your patience

View Article


Forum Post: RE: DAC161S997: Increased HART Communication Errors Due to Earth...

Hello Joseph, Any Updates? Regards, Yatin R

View Article

Forum Post: RE: ADS1298: Cannot get ID

Hi Ryan, Thanks for replying to my post. I will implement that a bit later as I don't have low value fixed resistors at the moment. Right now I am facing another issue. When I read the ID, I am also...

View Article


Forum Post: TPL0102-100: calibration resistance tolerance

Part Number: TPL0102-100 Tool/software: Application: use it as analog resistor for input. The tolerance is 20%, too big, can I do any calibration to reduce it?

View Article

Forum Post: RE: AFE58JD48EVM: Query regarding deterministic latency one...

Nitin, Can you please try instead of power cycling just do a global power down to device and clear that bit and repeat the experiment ? This 1 clock error can be in AFE or receiver(FPGA) .

View Article


Forum Post: RE: ADS8168: Whether support input Simultaneous Sampling ADC?

Taking this off-line for the moment. Check your email.

View Article

Forum Post: RE: ADS131E08: How to Suppress Industrial Frequency Noise in...

Hi Yivi Chan, Thanks for your update. BR, Dale

View Article

Forum Post: ADS127L18: ERROR pin sink capabilities. Driving a LED from this...

Part Number: ADS127L18 Tool/software: Hi, I would like to drive a LED to indicate an error, from the ERROR pin. I understand he pin is open drain with a 100k pullup resistor to IOVDD, but can this pin...

View Article
Browsing all 90415 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>