Forum Post: RE: ADS52J90EVM: Not able to evaluate using TSW14J50EVM
I've ordered the ADS52J90EVM through one of the partners of TI. Installed the software for both EVM's following the user guide. This is correct . Setup_ADS52J91_EVM_v1.0.0.exe for ADS52J91...
View ArticleForum Post: RE: ADS131B04-Q1: Provide the time sequence diagram of sending...
Timing to read MODE register (02h address) with RREG, the response is 0x0510 ,Compare and ask me the timing This is sent from my side, the only difference is that DIN default is a high battery, which...
View ArticleForum Post: RE: ADS1298ECGFE-PDK: Occurred ECG waves are not in the expected...
Hello Ryan, The ECG cable we are using is 5 lead ECG cable, which has RA, LA, LL, V1, and N. Is there a way to use 5 lead cables in ADS1298? I have attached the picture of register settings. On...
View ArticleForum Post: RE: AFE58JD48: AFE58JD48 configuration
I see that it is incrementing by 1 . Where is the repeated data ?
View ArticleForum Post: ADS1255: Recommend suitable IC
Part Number: ADS1255 Tool/software: Hi Bu Expert, Can you recommend a suitable device which is similar with ADS1255 but has a high SPI speed? Thanks. Regards, Charlie
View ArticleForum Post: AFE5832LP: Question regarding noise in the ultrasound image
Part Number: AFE5832LP Tool/software: Hello I am developing wireless ultrasound equipment using the AFE5832LP. When power is supplied and the AFE5832LP is initialized, the RX function operates...
View ArticleForum Post: RE: ADS1231: Zero drift calculation
Hi Keith, You mean calculation of change in offset voltage as you derived is same as calculations for zero drift? We want to calculate zero drift parameter of ADC . And in derived gain error...
View ArticleForum Post: RE: ADS8634: Trouble Reading Temperature Sensor
Hello, I have no oscilloscope capture but a script which gives the data frame send and receive, here is the result: As you can see, we send three times the command to read the temperature sensor, but...
View ArticleForum Post: RE: UCD3138128: UCD3138128
Hi Raphael, For converting .x0 file to .hex file for UCD3138128 please use the modified command line provided below. If the file is in the same directory: --infile test.x0 --pflash-checksum calc...
View ArticleForum Post: RE: ADS8861: The Dout pin gives a constant high (i.e '1') as an...
Hi Samiha , I figured it out . Turns out my ground pin was not properly touching the pad . I am getting a bias of 40 at 0V . That is acceptable or it can be further improved ?
View ArticleForum Post: RE: ADS52J90EVM: Not able to evaluate using TSW14J50EVM
Right.... But as I mentioned before, the Setup_ADS52J91_EVM_v1.0.0.exe is nowhere to be found. I understand that I need it, but I don't know how to get it. If i "google" this file the only hit is this...
View ArticleForum Post: RE: ADS1255: Recommend suitable IC
Hi Charlie Xiao, Can you please help provide the information I requested in the Notes section of the Thread Tracking Toolkit? Thanks! -Bryan
View ArticleForum Post: RE: ADS1262: ADS1612
If the customer wants to use all 10 ADC channels, should they refer to AInCOM, and should AINCOM be connected to ground or to REFOUT?
View ArticleForum Post: RE: ADS1262: ADS1612
Hi Arabella Zhang, The customer can refer to any analog input if they want to use 10x channels. They do not have to use AINCOM, the AINCOM pin could have been called AIN10 because AINCOM is like any...
View ArticleForum Post: RE: DAC38J84EVM: Osc_in Frequency of LMK
Hello The 122.88MHz reference clock is a typical telecom clock frequency (3GPP) that is based on the multiple of 3.84MHz
View ArticleForum Post: RE: ADC3643: Looking for an ADC with EVK that meets these specs
Hi Dalton, The ADC3664EVM would work, but unfortunately the recommended FPGA capture card TSW1400EVM is obsolete and has no replacement (according to TI customer support). If there is a suggestion for...
View ArticleForum Post: RE: ADC3643: Looking for an ADC with EVK that meets these specs
Hi Taylor, For the ADC3664EVM use the TSWDC155EVM for the data capture. Regards, Rob
View ArticleForum Post: RE: ADS1299：How to use differential input
Hi Di, Differential electrode inputs can be connected to the ADS1299 by using the INxP and INxN inputs pins for each channel. The SRB1 pin would not be used in that case. Regards, Ryan
View Article