Forum Post: RE: BP-DAC11001EVM: BP-DAC11001EVM
Hi Mark, Here are the gerber files. e2e.ti.com/.../0121.DC026B_5F00_Gerber.zip Best, Katlynne Jones
View ArticleForum Post: RE: DAC8568: Need DAC solutions suggestion!!!!
I would recommend 2 offerings. DAC81408: This will give you 8 channels, all the voltage ranges, but not the current range. DAC8775: This will give you 4 channels and cover all the voltage and current...
View ArticleForum Post: RE: AFE20408: About AFE20408 PCB macro and circuit symbol .
Hi Itoh-san, A small update, our team has started work on this project. I'll let you know when they give me a timeline. Thanks, Erin
View ArticleForum Post: RE: ADC102S021: Suitable ADC for low BW and low latency
Hi Nick, Theoretically that should be fine, but I am not really familiar with the TPS65130, and don't know if it would be optimal for your application. Feel free to repost this question on the power...
View ArticleForum Post: RE: DAC900-Q1: Question about the output of the DAC
Hi David, It might be a good idea to send me a block diagram of what you would like to implement ultimately. Per the datasheet, you can use a single stage opamp to DC couple to the outputs using the...
View ArticleForum Post: RE: ADC12DJ5200RFEVM: On-Board clocking issues
I'm still getting inconsistent results running from the EVM GUI - occasionally I get a SERDES PLL lock at the ADC but often I don't when re-configuring (tried with the scripts and GUI). What's the...
View ArticleForum Post: RE: AMC131M03: SPI communication with the device
Saleh, Can you confirm that my SPI command sequence is correct and should enable the HLDO: Thanks.
View ArticleForum Post: RE: ADC12QJ1600EVM: Conflicting Info on J25 Jumper Setting and...
Hi Roger, I have sent you an email regarding this question. If there are any follow ups can we do it through there if that is ok with you? Thanks, Eric
View ArticleForum Post: RE: ADC12DJ5200RFEVM: On-Board clocking issues
Hi Jeff, One thought in order to prove out the EVM is to try another JMODE, say JMODE 3 perhaps. This should be pretty easy to do if you are using the GUI and HSDCPro. If the PLL is not locking still,...
View ArticleForum Post: RE: ADC12DJ3200: SYSREF
The ADC12DJ3200 supports both AC and DC coupling of the SYSREF pins. To run in continuous mode then you would AC couple and to run SYSREF as a single pulse or multiple short pulses you will have to DC...
View ArticleForum Post: AFE5851: Analog Input channels influence each other with DC...
Part Number: AFE5851 Tool/software: 1. Testing for the AFE output setup All the signal VOUT_S , …, VOUT_S , VOUT_S ,…,VOUT_S are tied together, and could be adjusted by a on board pot The another...
View ArticleForum Post: RE: ADS1299: Inquiry Regarding Long-term Reliability and...
Dear Mr. Andrews, Thank you for your response. I also have a question regarding the Quality, Reliability, and Packaging information page you referenced ( www.ti.com/.../report . For the FAB process...
View ArticleForum Post: RE: TSC2046: how to improve the Sensitivity of touch
hi sir may i know how to set up the hardware level in sensing Sensitivity,thanks
View ArticleForum Post: RE: ADC12DJ3200: SYSREF
Hi，Kleckner Does TI have a chip that can convert the LMX2594 RFOUTB output signal to an LVPECL signal? Could you recommend one? Best Regards. Gu
View ArticleForum Post: RE: AMC1210: Coordinated Sampling of Two Filters
Hi Tom, We generated the 32MHz clock for the AMC1210 from our FPGA, held the clock off and then enabled it after setting the MFE bit. Works like a charm, we now have coordianted filter interrupts....
View ArticleForum Post: RE: AMC1210: Coordinated Sampling of Two Filters
Great news! Thank you for letting me know.
View ArticleForum Post: RE: TIPD109: I2C/SMBus of ADS1118
Thank you very much! Angel Have a nice day. Best regards, Tiger
View ArticleForum Post: ADS52J90: JESD protocol, eight-chip ADC synchronization problem
Part Number: ADS52J90 Tool/software: I want to use eight ADCs to form my system using the JESD protocol, but I'm having trouble providing a clocking scheme, I'd like to ask if I can satisfy the...
View ArticleForum Post: RE: DAC11001B: DAC11001B 0-5v
Hi, Please have bypass caps for all the op amps. Also, you have violated input common mode range of OPA828. It will not work. Look at the datasheet of OPA828 and read the section of electrical...
View Article