Forum Post: RE: ADS131M04: ADS131M04
also given Default commands(RESET, WAKEUP and Unlock) to see the Response as mentioned in Manual.
View ArticleForum Post: AFE4960PEVM: Dual AFE
Part Number: AFE4960PEVM Tool/software: Hi, We have purchased AFE4960PEVM board. I am using the EVM board to capture ECG waveform in Biosensing application. I am able to capture the wave for ECG 1 and...
View ArticleForum Post: ADS131A02: Problem with ADS131A02 and SPI Communication using esp32.
Part Number: ADS131A02 Tool/software: Hello, I am using an ADS131A02 and an ESP32-PICO-KIT for my project. In this case, the ADS131A02 is in synchronous slave interface mode, as I will be using SCLK...
View ArticleForum Post: RE: AMC1306M25: MTBD estimate
Hi Matthew, Thank you for your question. We don't have an MTBF figure in the datasheet, but we do include this plot about lifetime of the device: Please let me know if you have any more questions....
View ArticleForum Post: RE: ADS7142: Autonomous Mode GUI Operation
Hi Vinny, After trying this on my board, I can verify that I am experiencing the exact same issues that you are running into. I am updating the thresholds in the GUI, but it does not send anything...
View ArticleForum Post: RE: AFE4960PEVM: Dual AFE
Hi Iasikha - can you please share a copy of the python script as well as an image of your EVM jumper configuration? Regards, Ryan
View ArticleForum Post: RE: AFE4300EVM-PDK: AFE4300EVM-PDK / SBAS586 not found
Hi Adrien, It looks like you have access to the secure folder for the AFE4300 now. Please email biosensing_afe-support@list.ti.com if you have any additional issues. Best, Katelyn
View ArticleForum Post: RE: DAC39RF10EVM: How to control LMX1204 in DAC39RF10EVM
Matt, Thanks for your valuable reply. The input frequency of 1.8 GHz is multiplied by 2 to output 3.6 GHz. After performing a reset on R0, any register reads in the GUI will be 0x00. So I'm assuming...
View ArticleForum Post: RE: ADS7142-Q1: Schematic review
Hello Joel, This is used to remote the voltage change of the NTC as the temperature changes.
View ArticleForum Post: RE: DAC39RF10EVM: Output Not As Expected
Hello Geoff, Good day. Please refer to the attached file. e2e.ti.com/.../TI-DAC39-RF10-troubleshooting.zip Regards, TI-CSC
View ArticleForum Post: RE: DAC38J82: No waveform output from DAC38J82
Hi Chase, I have try the output format for the SDCLKOUT3 output to LVPECL1600mV, still not work. Also I have check the lane mapping from FPGA to DAC. My understand is if the mapping is wrong, the ILAs...
View ArticleForum Post: RE: ADS131M04: ADS131M04
That's correct we are using CPOL = 0 and CPHA = 1 configurations only. Also we are using standard SPI configuration so it the internal module which is capturing and generating the data. So I hope...
View ArticleForum Post: RE: ADC12DJ5200RFEVM: Trouble in setting JMODE5
Hello Eric-San, Thank you very much for your quick reply. Perhaps there is a mistake in the configuration on my FPGA board. HTG830 has two FMC+ connectors, FMC+(B) seems to have a sine wave coming in,...
View ArticleForum Post: RE: ADS7142: Autonomous Mode GUI Operation
Thanks for confirming the behavior. I look forward to any info when you have it! In the meantime, I'll try an Aardvark device to talk to the IC and see if I can get it to work for us. Do you happen to...
View ArticleForum Post: RE: AFE58JD48EVM: EVM for ultrasounfd imaging
Hi, What is the end application for this ultrasound imaging system ? Based on that we can suggest appropriate solution.
View ArticleForum Post: RE: AFE4960PEVM: Dual AFE
Hi Ryan, Thanks for the reply. I have connected the board as suggested in the EVM User Guide and used the python script given in the AFE4960PEVM. I have attached the EVM jumper configuration image and...
View ArticleForum Post: RE: ADS1286: ADS1286UL/2K5
hello , could you help give your fast confirmation quickly ? urgent case , thanks a lot
View ArticleForum Post: AMC130M02: Method for converting single end into differential signal
Part Number: AMC130M02 Tool/software: Hi All, I would like to know how to convert single end to differential signal. Is it possible to exchange information properly if I use AD2 fixed to GND? Or is...
View ArticleForum Post: RE: DAC38RF85: Search for a 100 MHz clock generator with 10 MHz...
Hello Kadeem, Thanks for these simulation results. It confirms that the LMK03318 is a good candidate, about phase noise, for this kind of application. Next step will be to check all the other features...
View ArticleForum Post: RE: AFE58JD48EVM: EVM for ultrasounfd imaging
Hello Sachin, Thank you for your reply. We have developed a wearable, small ultrasonic transducer array and would like to use TI’s EVM to verify its imaging capabilities. Currently, the number of...
View Article