Forum Post: ADS8689: ADC circuit question
Part Number: ADS8689 Our product uses ADS8689, which collects an analog signal that is a sine wave with a bias of 2.5V. AIN_P is connected to the analog signal, but we are not sure if AIN_GND can be...
View ArticleForum Post: RE: TSC2007: Need help with TSC2007
What is the difference between TSC2007.h, TSC2007_core.c and TSC2007_iio.c?? TSC2007_iio.c is for industrial input output, right?
View ArticleForum Post: DAC63204EVM: DAC63204EVM
Part Number: DAC63204EVM Hi, I am trying to communicate stm32 nucleo board to DAC63204EVM over spi. Hardware setup is as follows: 1. SCK (STM32 nucleo board) to SCLK( DAC63204EVM) 2. MOSI (STM32...
View ArticleForum Post: ADS8664: ADC reading freeze
Part Number: ADS8664 HI Sir I use the ADS8664 to reading the voltage ,sometime the ADC freeze after power on did you have any suggestion? or any power sequence need take care? thanks
View ArticleForum Post: RE: TPL0102-100: How to programme TPL0102-100 in Arduino IDE
Hi Katlynne, Thank you for the reply. Kind regards, Bright
View ArticleForum Post: RE: TSW14J57EVM: PC doesn't recognize
Hi Dmitriy, Let me look into this tomorrow and let you know. I think the TSW brd you have, REVB is only supported on older versions of HSDCPro. We are on REVE. And FW has been updated over time. What...
View ArticleForum Post: RE: ADC12DJ3200QML-SP: Thermal Information for CLGA and CCGA
Hi Noriyuki-san, Yes, this information is correct. Regards, Rob
View ArticleForum Post: RE: TSW14J57EVM: Problem with HSDCPro v6.0 - Error 1149
Hi Lei, It might also be helpful to send along a detailed block diagram of your test setup. Its confusing to us that you keep indicating that you want to use a trigger function, which is not needed in...
View ArticleForum Post: RE: DAC5675A-SP: Operating temperatures for the Engineering...
Hi Brandon, Correct, there are no differences in-between the two devices. Running the devices up to 70C will be fine. Regards, Rob
View ArticleForum Post: RE: ADS1262: the output has jitter
Hi Moon, The higher data rate, the higher noise, this is true on all precision ADCs. You can see the following noise table from ADS1262 datasheet, the noise at 1.2ksps data rate is much higher than...
View ArticleForum Post: RE: TSC2007: Need help with TSC2007
TSC2007_iio.c is the app, and depends on the api from TSC2007.c and TSC2007_core.c TSC2007_core.c is the basic code for TSC2007.c and TSC2007_core.c. Following snapshot is from the KCONFIG file from...
View ArticleForum Post: RE: ADS131M08: ADS131M08:
Hello Dale, Thanks for your reply. I will post the queries regarding signal conditioning on the Amplifier forum. still, if i have any doubt regarding this, I'll get back to you. Thanks for your...
View ArticleForum Post: RE: ADS54J69: Data output format & low frequency waveform
Dear Geoff Roth, If DC Cap (C152, C153) is replaced with 0 ohm, the waveform is improved as shown below, but it is not perfect. Additionally, I adjusted the impedenace circuit values after DC cap. It...
View ArticleForum Post: RE: TX7332: opening the TR switch
Hi Philippe, The state of the T/R switch is determined by the TR_SW_DIS register. The behavior of T/R switch has no dependence on power mode, be it default or dynamic. PDN_PUL_n and global power down...
View ArticleForum Post: RE: ADS122C04: ADC reading photodiode Constant Output. Interacing...
Hello, i made connection as follow A0 and A1 connected to ground RESET connected to 3.3V DGND and AVSS connected to ground REFN connected to ground REFP connected to 3.3V in between o.1uf capacitor...
View ArticleForum Post: ADS7138-Q1: about power dissipation
Part Number: ADS7138-Q1 Hi, Support Team we saw the ADS7138-Q1 functional safety FIT Rate, FMD and Pin FMA document: ADS7138-Q1 Functional Safety FIT Rate, FMD and Pin FMA as below table, the Ambient...
View ArticleForum Post: ADC3660EVM: ADC3660EVM
Part Number: ADC3660EVM Other Parts Discussed in Thread: TSW1418EVM We already have the Eval Board ADC3660EVM and understand that the Data capture Board TSW1400EVM is obsolete. Pl.advice if we can use...
View ArticleForum Post: RE: ADS131M08: ADS131 setup and communication
Ok , We would use the ADS131M08 to to make contemporary reading of weight on three scales. the three scales are connected to the same spi bus with different CS. Did you have previous similar...
View ArticleForum Post: ADS1118: PGA internal block diagram
Part Number: ADS1118 Hi, Can you provide the PGA internal block diagram of ADS1118? Looking at the datasheets of other TI PGA products, it seems that the internal block diagrams are disclosed. Thanks,...
View Article
