Forum Post: RE: ADS124S08: Issues when reading data by RDATA Command
Hi Jun Liu, [quote userid="522552" url="~/support/data-converters-group/data-converters/f/data-converters-forum/1355814/ads124s08-issues-when-reading-data-by-rdata-command/5176362#5176362"] 1) If I...
View ArticleForum Post: ADS54J60: Where to set M and S parameters in the JESD204C IP core...
Part Number: ADS54J60 Hello, We are trying to implement LMFS: 4-2-1-1 in the JESD IP core reference for the zcu102_8b_10b. We want to know which settings in "jesd_link_params.vh" need to be set for...
View ArticleForum Post: RE: UCD3138: UCD3138EVMCC64EVM-030
Hello, Yes, you can program UCD to blink LED. Output one I/O, on for some time and off for some time. You need a driver as well drive LED.
View ArticleForum Post: RE: UCD3138CC64EVM-030: Fusion Digital Power Studio iout isfault...
If the control card is unplugged, the input voltage to UCD ADC pin is undecided, you will see faults. You can connect the pins to ground.
View ArticleForum Post: ADS8664: SPI Communication
Part Number: ADS8664 I am trying to interface to the ADS8664 chip with SPI communication, but I am running into errors. This is the schematic that I am using. I am trying to enable channel 0, 1, and 2...
View ArticleForum Post: RE: ADS54J60: Where to set M and S parameters in the JESD204C IP...
Hi Ryan, These parameters aren't part of the Rx portion of the IP because the transport layer is not integrated in the TI JESD IP core. The mapping of lane data to samples is carried out in the...
View ArticleForum Post: RE: ADS54J60: Where to set M and S parameters in the JESD204C IP...
Thanks for the explanation Ameet. We have a couple questions regarding the JESDMODE register for LMFS=4211 In one table we see the following: It says that the register should be set to 0x4 for...
View ArticleForum Post: ADS1278: Physical details
Part Number: ADS1278 It appears from the datasheet that the ADS1278 has a metal bottom, it that correct? Will running traces underneath the component be a probelm?
View ArticleForum Post: RE: ADS131M08: ADS131M08:
Hello Prajwal Bhuse, Based on your requirements the ADS131M08 is a device to consider, however we do have devices that may work better for your application. Have you taken a look at the ADS124S08 ?...
View ArticleForum Post: RE: ADS122C04: ADC reading photodiode Constant Output. Interacing...
Hi Sayali, We have example C code for the ADS122C04 available here: https://www.ti.com/tool/download/SBAC299 Are you verifying you are setting the device properly and cycling through the right MUX...
View ArticleForum Post: RE: DAC3174: DAC3174 has no output
Hi Danny, I apologize for the delay, if you still need help, please send over the entire schematic. This would be helpful, you may have the DAC setup incorrectly. It would be helpful, to send over the...
View ArticleForum Post: ADS9224R: Limits on maximum time between CONVST and nCS being...
Part Number: ADS9224R Hi, We are looking at a design to simultaneously sample from at least 3x ADS9224R and grab the data from all 6 channels over the UPP interface on the F28379D. The goal is to...
View ArticleForum Post: RE: ADS131M08: ADS131M08:
Hello Josh Brown, Thank you for suggesting part number. Rest specs are complied with the requirement but it doesn't comply with our requirement as 8 differential analog input channels. Kindly suggest...
View ArticleForum Post: ADS114S08: Schematic Review
Part Number: ADS114S08 Hii Team, We are using ADS114S08 ADC in one of our Project. I want you to have a look on the schematic attached. As per our Design requirement i have added 2nd order 10 Hz LPF...
View ArticleForum Post: RE: DDC232: Supplying appropriate voltages from 5V FPGA
Brigitte , Input voltage is the 5V available from the USB bus. Output current would be in the 300–500 mA range, but if this is too high let me know and we can guide the design of the DDC232 circuitry...
View ArticleForum Post: ADS1278: How to measure 5V Analog IN using ADS1278
Part Number: ADS1278 What is the maximum input analog voltage that can be measured using ADS1278. Please find the attached schematic.
View ArticleForum Post: ADS131M08: ADS131 setup and communication
Part Number: ADS131M08 Hello , I am trying to use ADS131M08 for the first time. Where can I find a clear description of the start-up sequence and acquisition of converted data through SPI? The program...
View ArticleForum Post: RE: ADC121S021: For 16V application
If you are looking for more than 100mV of resolution, you might need a buffer. I suspect you would get what you are looking for without a buffer.
View ArticleForum Post: RE: ADS7066: ADS7066 data acquisition phase
Hi Vijay, It's probably easiest to look at Figure 6-1 on page 9 of the ADS7066 datasheet. The /CS pin going high stops the acquisition and starts the conversion process. Returning the /CS pin low...
View Article
