Forum Post: RE: ADS1248EVM-PDK: ADS1248EVM Web App constantly reports EVM...
Hello Bob, A continued thanks for all of your support. Below is a short and simple test i wrote just to bring the ADS1248 out of RESET write to its registers to setup for an ADC conversion and read...
View ArticleForum Post: ADS131M02-Q1: Question about ADS131M02-Q1 sample error
Part Number: ADS131M02-Q1 1.When i write CH1_CFG regs MUX1 [1:0] is 01b，i get a channel value is FFA417. Then, I write this value into CHI_OCAL regs, i I didn't get an expectation. So, I want to know...
View ArticleForum Post: RE: ADS131M02-Q1: Question about ADS131M02-Q1 sample error
One more question. When i use different gain values, whether these errors are also different.
View ArticleForum Post: ADS8588SEVM-PDK: Using the ADS8588SEVM as a stand-alone board...
Part Number: ADS8588SEVM-PDK Other Parts Discussed in Thread: ADS8588S Dear Technical Support Team, I'd like to use the ADS8588SEVM as a stand-alone board without PHI board. Q1-1 Is it possible to...
View ArticleForum Post: RE: ADS1261: Conversion time
Hi Bryan Thank you for your response. And, Let me answer to following question. Then, are there any appropriate devise? Will the customer sample the same channel many times, or do they want to...
View ArticleForum Post: DAC39RF10: TSW14J56, TSW14J57 support
Part Number: DAC39RF10 Other Parts Discussed in Thread: TSW14J59EVM , Hi, Does TSW14J56 or TSW14J57 support DAC39RF10? Thanks.
View ArticleForum Post: ADS1285: Register programming problem
Part Number: ADS1285 Hi, team. I'm having some problems with registers' configuration. "write_ads1285_register()"is the function I use to write all registers; "write_single_register(adress,data)" is...
View ArticleForum Post: RE: ADS1278: Cross-coupling or offset issue in differential...
Thanks Keith, I have decided however to move forward with the INA851. Would you suggest me to use for each channel of the ADS1278 the same circuit as in figure 9-9 of the datasheet and adding the 1 to...
View ArticleForum Post: TPL0401A-10: Want to check if this part is the correct solution
Part Number: TPL0401A-10 Hello team, the customer has asked a replacement solution for their currently used Single Digitally Controlled Potentiometer ISL95810UIU8Z-T (Rensas), . TI does not have a...
View ArticleForum Post: RE: DAC53202: DAC configuration is lost / incorrect on one...
Hi Katlynne, Thanks for your time on this, i found the issue in my code thanks to your help. I had mixed up eREG_DAC_1_CMP_MODE_CONFIG and eREG_DAC_1_VOUT_CMP_CONFIG in my set function. Kind regards,...
View ArticleForum Post: RE: DAC39RF10: TSW14J56, TSW14J57 support
Hi David, TSW14J56 is obsoleted and will not have any further new developments. The capture card for DAC39RF10EVM is TSW14J59EVM. https://www.ti.com/tool/TSW14J59EVM Thanks, Chase
View ArticleForum Post: RE: ADS4145: Schematics Snippet for Feedback
Viktor, I have taken a look at your schematic and only found one concern. The CLK input is AC coupled LVDS however there is no 100 termination prior to the series capacitors. Ensure that the correct...
View ArticleForum Post: RE: AMC1306M25: The data is smaller than the actual value after...
Hi Smith， Sorry to interrupt you again. I would follow this question. According to the customer's feedback: The MCLK to the AMC1306 is always out and the power supply is available. Only the FPGA...
View ArticleForum Post: LM98620: using HD-SDI receiver GS2970A with a Video Processor
Part Number: LM98620 Is it possible to use GS2970A HD-SDI Receiver with LM98620 video processor for converting HD-SDI input to LVDS display output?
View ArticleForum Post: ADS1118: how to convert thermocouple input millivolt to degree...
Part Number: ADS1118 Hello~ I'm testing ADS1118 with arduino mega and ADS1118-master library. Test circuit is referenced from Fig.50. Two-Channel Thermocouple Measurement System in ADS1118 datasheet....
View ArticleForum Post: RE: ADS1299: Daisy Chaining with internal clock gives garbage...
Update: 1. The same does not happen when using external clock. Image attached. 2. The values are now changing when we touch the sensors, but still not as stable as the first ADS. Are there any...
View ArticleForum Post: RE: ADS1299: Daisy Chaining with internal clock gives garbage...
Hi, In daisy chain configuration, you will be primarily looking at the DOUT of the first device which would be connected to the host processor. Since the 2nd device receives 2x the number of SCLKS,...
View ArticleForum Post: RE: ADS1298RECGFE-PDK: Can be used ECG_SHD_DRV as...
Yes, unshielded cable can pick up the power line noise.
View ArticleForum Post: RE: AFE4960: How do I calculate respiration amplitude and phase...
Hello Kanguk, My team is looking at your questions and will get back to you by this week.
View ArticleForum Post: RE: ADS1298ECGFE-PDK: Getting distorted waveforms with different...
Hi, Sampling at twice the highest frequency isn't sufficient to fully reconstruct the sine wave signals. You will see distortion in the output signals as you noticed.
View Article