Forum Post: ADS1118EVM: Urgent: DOUT not responding to CS pin as expected
Part Number: ADS1118EVM Hello, I am trying to use the ADS1118 EVM to develop some firmware on stm8 before I make the actual board and ADS1118 DOUT is not working as expected. I have used the EVM with...
View ArticleForum Post: RE: DDC112: What is manufacture valiation of output data when...
Hi Kazuya-san, Can they provide a graph of the distribution (a histogram of offsets)? If I understand right, they are saying that they got a Gaussian distribution of channels, all club together very...
View ArticleForum Post: RE: ADS1118EVM: Urgent: DOUT not responding to CS pin as expected
Hi Joseph, When I first tested with the EVM a while back, like more than a week ago, I was able to get it working and acquire correct numbers. But it stopped working on the same code the other day and...
View ArticleForum Post: TSW14J56EVM: Maximum data capture size
Part Number: TSW14J56EVM Hello, I am planning to use ADS52J65EVM along with TSW14J56EVM . I would like to be able to capture 8 channels at 125Msps, store on the DDR3 memory on TSW14J56EVM and transfer...
View ArticleForum Post: RE: ADC12DJ3200: Calculation of Full Scale Range on Each Inputs
Hi Jaydip It is possible to create a linear equation to convert from FSR register setting to mVpp. The default FSR setting of A000h (40960d) gives a full scale input range of approximately 800mVpp...
View ArticleForum Post: RE: TLC04: Trouble with 10V operation and 5V clock
I suppose that I can answer my own question. Apparently, LS needs to be biased to the mid-supply of the CLOCK, not the TLC04 . The datasheet simply says "midsupply". By moving the LS pin to a 2.5V...
View ArticleForum Post: RE: ADS124S08: Delsig Evaluation software - Data analysis tool is...
Hi Ramesh, Thanks for the update! This will be useful to others in the future I'm sure. Best regards, Bob B
View ArticleForum Post: RE: DDC112: What is manufacture valiation of output data when...
Hi Edu, Thank you for your strong supports. I see. I will try to get their row output data or graph you told and I will reply as soon as I get it. Also I will ask them to get the output data again with...
View ArticleForum Post: RE: TLC04: Trouble with 10V operation and 5V clock
Hi Joseph! I'm happy to hear that you figured this issue out with the TLC04 . Don't hesitate to reach out again if the need comes up!
View ArticleForum Post: RE: ADS1247EVM: Establish communication ADS1247EVM to ADCPro
Hi Dominik, I must say I'm very stumped. It seems like the program is not finding the files or that they may be corrupted. I used the same download as you, so I don't think there is a file corruption....
View ArticleForum Post: ADS1248: Communication with ADS1248
Part Number: ADS1248 Hi, I am trying to communicate from my microcontroller over SPI to ADS1248 . I am following pseudo-code mentioned in the datasheet. But I am not able to read any register. Is there...
View ArticleForum Post: RE: ADS1282EVM-PDK: Anything in the EEPROM would prevent me from...
Hi Marti! I actually like Plan A. De-soldering the EEPROM and mounting it 'stand alone' to the MMB0 is actually not that bad of an idea. There are screw terminals on the MMB0 which you can use to wire...
View ArticleForum Post: RE: ADS1248: Communication with ADS1248
Hi Suraj! Welcome to our e2e Forum! Can you give us an idea of how have your ADS1248 connected to you micro controller? Perhaps post a schematic and maybe provide some detail (O-scope or logic...
View ArticleForum Post: RE: DDC112: What is manufacture valiation of output data when...
No problem. Just 1ms each is good (CONVL=CONVH=1ms). It doesn't really matter as long as it is short and we know the number. Regards, Eduardo
View ArticleForum Post: RE: ADS131E08EVM-PDK: LabVIEW project file for ADS131E08EVM-PDK
Hi Joseph, Thanks for rapid response!!! Yes.. I checked with folder mentioned by you. There are .VI files are available. But I need complete project file and all VI. So that can modify small things and...
View ArticleForum Post: RE: ADS1298: Ads1298 Daughter card EEPROM CONTENTS
Hi thanks . my question is that the MMB0 board will take data from ECG board without the EEPROM connected or i am not sure my connection is got other issue . Please advice . -pragdhees
View ArticleForum Post: RE: DAC38J84: issue with self test
Hi Eben, I am giving DAC reset (resetb pin of DAC) before programming it. I will check and let you know about the spurious signals on increasing the span of the spectrum analyzer. Thanks and Regards, suma
View ArticleForum Post: RE: ADC12DJ3200EVM: TIDA-1021 Sync board External OscIn Option
Hi Ajeet, Thanks for the help. The boards are now sampling at 4 GHz with a 10 MHz external reference to the TIDA-01021 , but there are still some issues. After loading the .ini firmware in HSDC Pro to...
View ArticleForum Post: RE: TSC2046E: PENIRQ operation and capacitor of X / Y line
Thank you Hamamoto-san.
View ArticleForum Post: RE: TSC2046E: PENIRQ operation and capacitor of X / Y line
Hello Hamamoto-san, We've reviewed the material, thank you for sharing. The schematic looks appropriate. Can you confirm two more things? 1.) What communication method are you using to communicate with...
View Article
