Forum Post: AFE5818: Require 16ch AFE5818 TX EVM W/STHV748 documents details
Part Number: AFE5818 Hello, Please find attachment,here i attached one image file of Ti's board. TEXAS INSTRUMENTS : 16CH AFE5818 TX EVM W/STHV748 (INT USE) 22 MAY 2013 If anyone have details/...
View ArticleForum Post: RE: AFE5818: Require 16ch AFE5818 TX EVM W/STHV748 documents details
Waiting for your favorable reply, Regards, Kiran
View ArticleForum Post: RE: ADS131A02: DRDY data line not behaving as expected
Eddie, Thanks for your post. Based on your write up I was unclear about the problem that you were seeing. Are you concerned that the /DRDY is often low? The act of /DRDY transitioning low indicates a...
View ArticleForum Post: RE: ADS131A04EVM: ADS131A04EVM
Kost, I'm not sure what is going on. I did have a chance to use the ADS131E04EVM earlier today, and I didn't see any problems with line cycle noise. For your test, I would start with focusing on what...
View ArticleForum Post: RE: ADS131E08EVM-PDK: Not able to see correct ADC input on...
Tejaswini, I'm sorry that I didn't answer you earlier today. I just didn't have a chance to put together the ADS131E08EVM to look at the setup. If you do have the EVM power supplies set to ±2.5V, then...
View ArticleForum Post: RE: ADS124S06: ADS124S06 Digital Domain at PGA=64 and 128
Hi Joachim, Thank you very much. Masa
View ArticleForum Post: ADS1262: TI REF3012 vs TI INA125: Who is the best for my ADS1262
Part Number: ADS1262 Hello people! With ADS1262 PGA set on Gain 32, the full scale is 78mV, so my load cell -with its 20mV max output- isn't able to exploit ADS capabilities. I have two solutions: I...
View ArticleForum Post: RE: ADS131E08EVM-PDK: Not able to see correct ADC input on...
Hi Joseph, Yes, we did check the input voltage with an oscilloscope and it is showing correct Sign wave with 50 mV Peak to Peak Voltage amplitude and 50 Hz freq. (We are giving using Function generator...
View ArticleForum Post: RE: ADS114S08: Data output from ADS goes to zero intermittently
We probed the power supply but no noise was observed. We also read the FL_POR flag in status register and found the device was entering a POR state. However when we checked the power on condition of...
View ArticleForum Post: ADS5292: Decimation by 8 with custom coefficients not working
Part Number: ADS5292 Hello, we are using the ADS5292 with 80MHZ ADC input clock. We have enabled the decimation filter with custom coefficients and decimation by 8. When setting the output data rate to...
View ArticleForum Post: RE: ADS131A04EVM: ADS131A04EVM
Joseph, I attempted the second case: if i plug in the oscilloscope getting good!) In my board broken usb connector, and the wire is soldered straight but not sealed braid. Where to solder the braid?
View ArticleForum Post: ADS7253: ADS7253 Write/Read issue
Part Number: ADS7253 Hello There, We are using ADC Part No# ADS7253IRTER. The ADC is connected to MCU/DSP processor on the SPI Port. The MCU/DSP processor support the standard SPI Mode 0, 1, 2 and 3....
View ArticleForum Post: DAC7821: Output is not coming for the input 2.5V,5V and 10V
Part Number: DAC7821 Hello, I am using DAC7760 IC which is a current output and parallel DAC. I have interfaced it to a microcontroller (Infineon XMC4800). The output is not coming for the input data...
View ArticleForum Post: RE: DAC7821: Output is not coming for the input 2.5V,5V and 10V
Sorry, In description it should be DAC7821 .
View ArticleForum Post: RE: ADS1256: Power Drain during channel switching
Hi Chris, Thank you for the response. We changed the AVDD of ADS1256 to 5V from 3.3VDC. All channel sampling is done with PGA set to 1. As the AVDD is set to 5V, the input voltage AINx should not be a...
View ArticleForum Post: ADS54J64: Power Consumption if used as single channel ADC
Part Number: ADS54J64 Hello Team, what is the power consumption if I use only 1 channel and switch off the remaining 3 channel with PDN_CHB/C/D. According data sheet it is 625mW per channel, but I...
View ArticleForum Post: ADS131E08: Low pass filter cut off frequency requirement analog...
Part Number: ADS131E08 hi, I am using ADS131E08 for voltage measurement in my project.I will be sampling at 8 kHz. The low pass anti aliasing filter cut off frequency should be less than 4 kHz,...
View ArticleForum Post: TSW14J56EVM: TSW14J56EVM, HSDC Pro, and third party FX3 device
Part Number: TSW14J56EVM I have a working Windows 10 configuration using the TSW14J56EVM and HSDC Pro. When I then add another USB 3.0 device which also uses the Cypress FX3 (a SignalHound BB60C...
View ArticleForum Post: RE: ADS131A04EVM: ADS131A04EVM
Kost, I'm actually not completely sure where the USB cable shielding is supposed to be connected. I thought that the shield should be connected to the GND, but through a resistance and filtering....
View ArticleForum Post: RE: ADS7223: CID in full clock mode
Hi Lutz, I'm still looking into what this could be caused by. Just to confirm - which SDOx is the customer using? Are the outputs coming out on the same SDOx or separate SDOA and SDOB? Regards,
View Article
