Forum Post: RE: LM49352 timing info
Hi A.. In ESP, there is an App Note for interfacing with i2S: Interfacing an I2S Device to an MSP430 Device (Rev. A) . The format acceptable is shown in the LM59352 datasheet Fig 64. ~Leonard
View ArticleClik here to view.
Forum Post: RE: ADC128S102, ADC output value stopped when any value reached
For a reader understand, i add some photo.2.7V, 0010 0000 00003.5V, 0010 0000 0000output ADC signal was same.
View ArticleForum Post: RE: problem in reading system monitor ADS1148
Hi Manoj,Are you sure you are using the correct conversion formulas? Can you send me the formulas you are using to convert the codes to volts/temperature? Can you also send me the raw digital codes...
View ArticleForum Post: RE: ADS5282 EVM Problems
Hi,I have never actually caught any devices that have *been* programmed that lost the programming - all the ones that I could track down the actual chain of events were ones that we simply skipped the...
View ArticleForum Post: channel switching problem in ads8330
hi,i am using the ads8330 in data logger.i have interfaced theadc to mcu through the SPI mode in manual trigger and manual channel select mode with that i am unable to get the data from another...
View ArticleForum Post: RE: How to get the RD195 arc detect software package ?
Hi Joachim,Thank you for the feedback.Tchapo
View ArticleForum Post: LM49352 kernel driver
We are developing new device using LM49352 chip. Could you tell me please, do you have LM49352 driver for newer kernel? In current kernel we could find only driver for LM49453, but not datasheet for...
View ArticleForum Post: RE: ADS1x9xECG-FE kit contents
Pl tell me if we connect 4 lead ecg cable from patient to demokit db 9 connector and also connect to Mini usb to laptop then 3 terminals analog & digital voltage are required for live ecg or any...
View ArticleForum Post: RE: PCM5102A - questions
Hi,this is probably OK, because PCM5102A support only BCK 32FS and 64FS in PLL mode. Details are in datasheet on page 12. In my opinion it will be better to use SCK (MCLK) from your USB->I2S...
View ArticleForum Post: RE: Inquiries regarding error descriptions on DAC7554
Mejia-san,Thank you for your prompt reply. We could understand the difference between zero-scale and offset error.Meanwhile, with regard to error variation per channel, it is difficult for them to...
View ArticleClik here to view.
Forum Post: RE: ADS1248 interfacing msp430g2553 using spi
hi Bob, 1. I'm using CCS now for my project but when I debug code base code you sent me the warning appear. How can I fix that?2. With signal-ended measurement, can I use circuit diagram of ADS1256 for...
View ArticleForum Post: RE: ADC12010/20/40 VS ADC12L063/066 How TO use ＊OEinput
Hello,Conceptually, the additional noise created in the ADC12040 as a result of additional capacitance on the digital output pins is the same for ADC12L063/066. In both cases, the additional...
View ArticleForum Post: RE: Reg MSC1210y5 program is frequently deleted.
Dear Bob, As per our previse mail discussion for MSC1210Y5 code corruption. Now testing in site conditionMy program part of code something corrupted, particular module function...
View ArticleForum Post: RE: ADS7961 SPI manual mode
Jake,I apologize for this delay in replying to your post.I am trying to get my hands on a Hercules Launchpad and a ADS7961 board, but in the meantime here are some questions based on your post.You...
View ArticleForum Post: RE: TSW14J56 EVM
David,The full part number for the Altera device is 5AGZME1E3H29C4N. If you need firmware to help you with your design we can provide some examples, both Altera and Xilinx based. The main purpose of...
View ArticleForum Post: RE: ADC EVM recommendation
Hi Tom,Attached is my first version TINA-TI file. As it is it should work, though I have not yet implemented it on the board. Figuring out what to desolder/short from the schematic should be fairly...
View ArticleForum Post: RE: tvp5158 4D1 16bit --- omapl138
Andrew,The is no way to eliminate the blank lines. These blank lines are inserted in order to compensate for the fact that each analog video stream that is being decoded is completely asynchronous to...
View ArticleForum Post: Ads1298 with raspberry pi
Hello ,I am a french student, and i have a ECG project to do,I understand that the MMB0 board is used to read data from ADS1298 and send it to the PC through USB.I wanted to know if it was possible to...
View ArticleForum Post: RE: ADS129xECG-FE missing libusb0.dll on Windows 7
consult this link :http://e2e.ti.com/support/data_converters/precision_data_converters/f/73/t/247226.aspx
View ArticleForum Post: RE: ADS5400 data output seems to keep resetting
Hi,You do not need to use the SPI port to program internal registers to get basic operation of the ADS5400. Our ADS5400 EVM will operate with the TSW1400 or TSW1405 capture cards without having to use...
View Article