Clik here to view.
Forum Post: RE: SRC4190 TDM mode
Dear Flora, Thank you very much for your quick reply. I have explained our use case in more detail. I hope this clears any misunderstanding. Our use case is as shown in the below figure.When all three...
View ArticleForum Post: RE: LDC1000 thickness of conductive target
thicknessskin depthsensitivty...
View ArticleClik here to view.
Forum Post: RE: ADS1256
Hi Chris,I figured it out, the ADS is working now:) The problem was that I am using an evalution board that also includes a temp sensor as another slave on the spi bus and I forgot to set the CS for...
View ArticleClik here to view.
Forum Post: RE: ADS54RF63EVM board functionality testing
After connecting the ADC to FPGA, I looked how the bits are varying using the chipscope. I get the following pattern.MSB varies at same frequency as input. Next bit is an inverted waveform of MSB! And,...
View ArticleForum Post: DIR9001 preamble detection
HelloMy client is using DIR9001 for AES/EBU decoding.Here are questions---------Q1 latency of Error for preamble If Preamble can not be detected, Error(#27pin) goes high after 3/fs of error...
View ArticleForum Post: RE: AIC3104 DAC output switching
Hi Don,Did your colleague have any suggestions regarding the register writes? Regards,Donald
View ArticleForum Post: RE: Trying to Identify Cable for TSW1400 to ADS5404 and a DAC34H84
Kang,Thank you for your reply. I am already aware that the devices can be connected. I am trying to identify the cable that connects the digital interfaces together. Unless you are implying that I...
View ArticleForum Post: RE: 16 bit dac ,4 channels ,about from 500khz to 1mhz
You need to use Nyquist theorem: for 1MHz signal you should take at least 2MSPS (2 million samples per second)If you click 16 bit 4 channel DAC on the table another table will open. You will be able to...
View ArticleForum Post: RE: SRC4190 TDM mode
Hi,Prachi,Thanks for your patience. I am sorry for my misunderstanding.Now I understand your concern.1.You are right, the processor will receive the 6 mono channel TDM data from the SDOUT pin of Slave...
View ArticleForum Post: RE: Interfacing LDC1000 EWM with Tiva Connected Launchpad
Same situations here, I tried to TM4c123GLX.But no reply from LDC1000.Any ideas are welcome.Thanks in advance.Kim Jaewoo
View ArticleForum Post: RE: PCM5310 problem: clipped output
I'll try to ask to customer whether output of 2Vrms can do by only DAC or not.Anyway, my question of analog input is about the internal circuit of IC.As my understanding, VCCH is for the driver...
View ArticleForum Post: Question for connecting DAC101C081 with MSP430F5172
Hello,I recently met a problem. I tried to connect the DAC101C081 (6 pins, I2C) as slave mode with MSP430 (master mode). I connected ADR0 of DAC to GND and Va to 5V. However, when I tried to transmit...
View ArticleForum Post: ADC
can anyone get me a best document to understand ADC to its depth with all parameters, conversion process etc.
View ArticleForum Post: Using ADS1282 for 4 wire RTD temperature mearurement
Hi,I want to use ADS1282 for 4 wire temp measurement. I am not concerned about the 50/60Hz rejection since it is battery powered. Just want to know the feasibility.Regards,Akshat
View ArticleForum Post: ADS1282 front end for deep sea pressure change measurement
Hi,One of my customer is looking to interface ADS1282 with a differential pressure sensor. The Pressure sensor is to be used on the sea bed and will measure the changes in height. The output of the...
View ArticleForum Post: RE: DAC7822 internal resistors mismatch
Hi Eugenio,Unfortunately the product we are working on is not announced yet and I can't share any info at this point. I'll keep you posted with infos and schematics as soon as we are close to a...
View Article