Forum Post: RE: How to use motherboard MMB0 which ADS1298 plug into?
You should receive more information via email
View ArticleForum Post: RE: ESD protection for ADS1292 ECG Front end
For legal reasons, we are prohibited from discussing patient protection/interface circuitry. You might search the forum to see if other persons have commented on specific findings.
View ArticleForum Post: RE: ADS5263 sampling timing
Hi Christian,Thank you for your fast reply.I understand the timing.ThanksNaoki
View ArticleForum Post: RE: Data acquisition system with hardware for Digital signal...
Hi Christian, Thank you for your helpful response !!I also would like you to help me clarify the following doubts : 1) Do i have to save the acquired data in some kind of card for further processing or...
View ArticleForum Post: RE: JESD204B Xilinx/TI ADS42JB69 Interoperability
Fabu,I have requested these projects from Xilinx.Regards,Jim
View ArticleForum Post: RE: Noise on TVP5146
How long is this part likely to be in production. I see its listed under Legacy Video Converters!RegardsMike
View ArticleForum Post: RE: TVP5158 JTAG issue
Hi Steve,Thanks for your reply. However, we wnats to confirm what mode will TVP5158 be if the JTAG pins are puled up with resisotors (it is same design with EVM). Because I2C bus is not always have...
View ArticleClik here to view.
Forum Post: ADS1299 Error Popup
Hello,I am using the ADS1299EEG-FE PDK in order to measure single-ended EEG signals. I configured the jumpers as shown in the attached picture and checked other forums to see if it was done correctly...
View ArticleForum Post: RE: ADS1256
Hi Thomas,Welcome to the TI E2E Forums!There is some ADS1256 Example Code with the corresponding logic analyzer data posted on this related E2E thread:...
View ArticleForum Post: RE: ADS1255 wrong data appear after a random time
Hi Laurent,A system calibration should always take precedence over a self-calibration (the system calibration will be more accurate). The self-calibration will not account for your signal conditioning...
View ArticleForum Post: RE: ads1256 DRDY and timing
Hi Gerald,Welcome to the TI E2E Forums![quote user="Gerald Faulhaber"]In general, it is save to trigger always on the falling edge of the DRDY and then start SPI communication?Or are there situations...
View ArticleForum Post: RE: ADS1259 Internal 2.5V reference
Chris,Thank you for confirming I can use it the ADC in the mode I intended. What would happen if I apply 5V to VREFP and not use the internal reference? would it behave the same way?You have an...
View ArticleForum Post: RE: TVP5158 line-mux capture with DM368 - line jumps at beginning...
I'm trying to understand what you are saying.Is it in your opinion that the DM's VPFE may be missing super frames because it needs the vertical blanking period to do some processing while the input is...
View ArticleForum Post: RE: Digital to Analog Converter for arbitrary waveform generation
Can I give the arbitrary waveforms (with sampling period information) through the GUI to the DAC EVM.
View ArticleForum Post: RE: LDC1000EVM API
I too would like this software, any further word on when it will be available?Thanks.
View ArticleForum Post: Questions about the ADC function of AFE5808
Hello: I am using the AFE5808 in my ultrasonic system design, but now we are facing a problem: we can't get the ADC data from the LVDS outputs. I connect a sine signal of 600mVpp to the AFE, but...
View ArticleForum Post: RE: ADS1248 interfacing msp430g2553 using spi
Hi Bob,Could you show me how connect a analog device to ADS1248. For Example must connect 4 analog signal 4 - 20mA to ADS1248Thanks and best regards,Thuy Tran
View ArticleForum Post: RE: TSW1405EVM - input LVDS common mode voltage
Hi,I just wanted to add that while the bit rate for the LVDS data is rated for 1000Mbps, the clock for the LVDS data is in DDR format so the clock would not be at 1000MHz. The max clock rate into the...
View ArticleForum Post: Initializing an external ADC in C language
Hey smart people, I am a very amateur programmer and have been tasked with a problem that I am having some trouble with. I have an external Analog-to-Digital Converter, the TLV571, and I need to...
View Article