Forum Post: ADC3563: Is LVDS FCLK needed in any case or is bit slipping on RX...
Part Number: ADC3563 Tool/software: Hi, I want to receive samples from the ADC3563 using an Intel Cyclone 10 LP FPGA. The Quartus design suite only offers an LVDS RX IP with data and clock inputs —...
View ArticleForum Post: RE: DAC61408: DAC Not Outputting on All 8 Channels – ZCU104 FMC...
Hi Syazwani, Please share the measured value of each power pins on the DAC61408 device. And capture and share the scope plot for SPI lines. Thanks, Sanjay
View ArticleForum Post: RE: ADS131M08: ADS131M08
Hi Dale, because the project is already advanced, we would like to avoid changing the component. So are there minimum and maximum values and some informations about the temperature dependence...
View ArticleForum Post: RE: ADS7924: ADS7924 I²C Read Causes Glitches and Sudden Jumps in...
Hi sw w, I did not realize that you were not exiting auto-scan mode before reading data. This mode of operation is meant to be used as a system monitor in conjunction with the individually...
View ArticleForum Post: RE: ADS8664: The output reference voltage is low
It's hard to debug over the forum if you don't have the tools to verify that you are not exceeding any of the datasheet limits. Is the reference oscillating or is the 3.6V level a stable DC value? You...
View ArticleForum Post: RE: THS1206: data_av line always keeping high
Hi Varun, Welcome to our e2e forum! The THS1206 is a pipe line converter and needs the CONV_CLK to toggle 7+TL times before DATA_AV goes active. Once DATA_AV goes active, you can start reading the...
View ArticleForum Post: TSC2007: Touchscreen rarely doesn't work
Part Number: TSC2007 Tool/software: Hi team, My customer has been using TSC2007 for their product which is in mass production. However, they face issue that touchscreen rarely doesn't work....
View ArticleForum Post: RE: ADS1220: On Raspberry Pi, read register goes wrong, CS and...
Hi Dale, Here is a zoom in of the plot. I hope it will help. Have a good day Soizic
View ArticleForum Post: RE: LSF0101: LSF0101
Hello Ishwar, Our apps team is currently out of office due to US holiday. We'll return back on Monday and help answer your question. Thank you! Regards, Josh
View ArticleForum Post: RE: DAC39RF12EVM: Setup for DAC39RF12EVM
Hi Kramer I generated the tones on the FPGA using the High speed data converter @4GHz. with the same sampling rate of 10.24G using the Jmode0. I tried refreshing the DAC GUI, it doesn't seem to...
View ArticleForum Post: RE: ADS1220: On Raspberry Pi, read register goes wrong, CS and...
Hi Soizic GIBEAUX , Today is a holiday in the US, we will respond to your question next week. Thanks for your patience -Bryan
View ArticleForum Post: RE: ADS1235EVM: ODR Selection for ADS1235 EVM
Hi Nimit Vachhani, Today is a holiday in the US, we will respond to your question next week. Thanks for your patience -Bryan
View ArticleForum Post: RE: ADS131M08: ADS131M08
Hi Florian Struwe, Today is a holiday in the US, we will respond to your question next week. Thanks for your patience -Bryan
View ArticleForum Post: RE: DAC61408: DAC Not Outputting on All 8 Channels – ZCU104 FMC...
Hi Sanjay, I hope you're doing well. I don’t have access to the board at the moment, but I’ll make sure to send over the required details first thing on Monday morning. Just to confirm — you would...
View ArticleForum Post: RE: AMC131M03: CRC issue
Hi Jiri, Thanks for your suggestions. As suggested, SPI CLK voltage reduced from 5 to 3.3V. Still the problem persists. As required below is the DVDD capture. Does noise at sync/reset pin can cause...
View ArticleForum Post: RE: TSC2007: Touchscreen rarely doesn't work
Hi, Our TSC expert is out of office and can update this thread early next week.
View ArticleForum Post: ADS1299: The difference between single and dual power supply
Part Number: ADS1299 Tool/software: Hello , there are 2 ways about power supply in the datasheet. I want to know which is best way in EEG acquisition.If AVDD–AVSS'max =5.25V means I can choose...
View ArticleForum Post: RE: ADS8664: The output reference voltage is low
Hi Tom, We have submitted the FAR and TI CQE feedback this is check in TI E2E firstly, and we have review the schematic diagram is well in this thread, So we want to know if there are any p ossible...
View ArticleForum Post: RE: ADS8664: The output reference voltage is low
Zhang, Is this happen on only one board or are there multiple boards showing an issue? If only one, perhaps it is a chip issue. If multiple boards show the same problem, it might be related to the...
View ArticleForum Post: ADS1292: About how to do with RESP Pin/IN3N IN3P if I do not want...
Part Number: ADS1292 Tool/software:
View Article