Forum Post: ADS131E08: Read Data with RDATA command and the result is corruption
Part Number: ADS131E08 Tool/software: Hi，TI's specialist. When I used ADS131E08 to collect data, the data I returned was wrong, and I used RDATA command . The hardware interface is that the power...
View ArticleForum Post: RE: ADS131M02: ADC always reads 0x8000 no matter what the input...
Joachim Wuerker Thanks for helping me with this. Here's me trying to set the MUX[1:0] to 01b. Verified my write to make sure it is 0x01. See the response frame on the right. Here's what I read on the...
View ArticleForum Post: RE: ADS1213: Checking support on ADS1213E part
Thanks Kyle. One of your colleague has stated that ADS1213E is Obsolete and no more inventory on these parts. Can you reconfirm on this? If you believe that you could support, for how long years we...
View ArticleForum Post: DAC7573: I2C recovery
Part Number: DAC7573 Tool/software: I would like to ask how to recover if the DAC7573 leaves the SDA line at L. My hardware does not allow a power on reset by turning VDD off and on. Is there another...
View ArticleForum Post: TPS63060:はんだ付け条件
Part Number: TPS63060 Tool/software: こんにちは。 はんだ付け条件としてN2は必要ですか?
View ArticleForum Post: ADC12DL2500: temperature sensing
Part Number: ADC12DL2500 Other Parts Discussed in Thread: LM95241 Tool/software: Hi, We have a legacy system where we are replacing ADC to ADC12DL2500. Can we continue to use LM95241 for ADC...
View ArticleForum Post: RE: LMP92066: Getting started with the programing of the IC
Hi Erin, For GaN configuration, i want to achieve the below sequence- 1.) FETDRV1 and FETDRV0 should be -5V at 24C 2.) Then after 5 seconds FETDRV1 should be set to -2.8V. 3.) Then after 10seconds...
View ArticleForum Post: RE: DAC39RF10EVM: Output Not As Expected
Hello Geoff, Good day. We think we understand the issue at this point. It seems we can't generate repeated bit sequences longer than ~128 before we get limited by this high-pass filtering due to AC...
View ArticleForum Post: RE: DATACONVERTERPRO-SW: Using ZCU102 With HSDC Pro Gui
No, it is designed to work for capture cards released by TI.
View ArticleForum Post: RE: ADS1299: Measure using BIAS
Hi Ryan, Do I ignore INP and INN, and just suppy sine waveform to BIAS electrode when software config as BIAS measurement? Regards, Toan
View ArticleForum Post: RE: TPS63060:はんだ付け条件
Hi， Kind reminder that thread in E2E will assign to product line but not local field team. So please use english in your description, thanks. About your quenstion, i am sorry i do not know the mean of...
View ArticleForum Post: RE: TPS63060:はんだ付け条件
Is nitrogen gas mandatory as a condition for reflow soldering?
View ArticleForum Post: RE: AFE7225: Differential Clock Input Level
Is there a spec for common-mode range that can be input to the clock buffer? Instead of AC coupling the differential signal, I could instead DC couple the clock (Vcm ranges from 0.8 - 1.0 V) which...
View ArticleForum Post: RE: ADS131E08: Read Data with RDATA command and the result is...
Hello, It appears that you are using different SPI modes. The ADS131E08 should ALWAYS use SPI settings CPOL=0, CPHA=1. SCLK should idle low, the ADS131E08 captures data (DIN) on the falling edge of...
View ArticleForum Post: RE: AFE7225: Differential Clock Input Level
Hi Brady, I would stay with an AC coupled input to the clock pins. I reread your post, are you planning to drive the clock single-ended, SE, or differential, DIFF. If DIFF, then there is no need to...
View ArticleForum Post: RE: ADS1018: ADS1018 SPI communication issue
Hi Shyam, I'll take a closer look and get back to you by tomorrow. Best Regards, Angel
View ArticleForum Post: RE: ADS131M04: Data returned from ADC abnormal
Hi Frank, For best performance and better immunity to electrical transients/noise, I highly recommend the customer use the /CS pin. In this case, if there is a glitch on the SCLK line, only the...
View ArticleForum Post: ADS52J90: Runtime change in clock to data delay
Part Number: ADS52J90 Tool/software: Hello! I have been using the ADS52J90 on a custom PCBA, and we have so far tested the design on about 15 or so PCBAs. I recently found that, on one PCBA, the clock...
View ArticleForum Post: RE: AFE7225: Differential Clock Input Level
We are driving it with differential, I was just under the impression from the tagged thread in the original post that the lack of Vcm bias could still be an issue. If the Vcm buffer is down at startup...
View ArticleForum Post: ADS1282: noise floor spike
Part Number: ADS1282 Tool/software: Hello, We are using ADS1282 ADC, sampling rate 64KHZ; data size 24 bit. Shorting ADC input to middle ground point(2.5VDC). Trying to collect noise floor. Getting...
View Article